D-PEMX-DY-23試験無料問題集（138題）「EMC Dell PowerEdge MX Modular Deploy 2023 認定」

出題：1

An implementation engineer prepares to install a PowerEdge MX7000.
Which serial cable do they use?

A. USB-A --> USB-B

B. DB9 --> Micro DB9

C. USB-A --> Micro USB-B

D. DB9 --> DB9

正解：C 解答を投票する

出題：2

What configuration is supported for a fully populated MX740c compute sled?

A. 1 Fabric A mezz card
1 Fabric B mezz card with Fabric C being integrated into the system board

B. 2 Fabric A mezz cards 2 Fabric B mezz cards
2 Fabric C mini-mezz cards

C. 1 Fabric A mezz card 1 Fabric B mezz card
1 Fabric C mini-mezz card

D. 1 Fabric B mezz card
1 Fabric C mezz card with Fabric A being integrated into the system board

正解：C 解答を投票する

出題：3

A data center team is working on a solution to monitor and manage data center devices from anywhere.
Which feature can be configured to perform these tasks?

A. OIDC

B. OME-M

C. QAT

D. OMM

正解：D 解答を投票する

出題：4

An administrator is asked to install and power-on a new MX740c sled in an MX7000 chassis. The administrator inserts the sled and presses the power button. They notice that the power button LED is blinking green. After a short time power button turns to solid green and the server finally turns on.
What operation was in progress when the power button was blinking green?

A. iDRAC was updating firmware

B. Lifecycle Controller update was in progress

C. iDRAC was booting

D. Lifecycle Controller was taking firmware inventory

正解：C 解答を投票する

出題：5

What is a characteristic of MX7000 networking in Scalable Fabric Mode?

A. All switch interfaces are assigned to VLAN 1 by default and are in the same Layer 2 bridge domain.

B. Layer 2 bridging is disabled be default and interfaces must join a bridge domain (VLAN) before being to forward frames.

C. Enabled by default, all switch-specific OS10EE capabilities are available.

D. Available on MX9116n FSE and MX7116n FEM but not on the MX5108n.

正解：D 解答を投票する

出題：6

A technician replaces a failed Management Module in an MX7000 chassis group. After the technician leaves the site, the administrator reports that the lead chassis is no longer able to communicate with its members.
How can OME-M be used to confirm the cabling configuration?

A. View the health status of the lead Chassis Management ports

B. View the health status of the lead Chassis Management Module

C. View the I/O module topology map from the lead chassis

D. View the topology map from the Group Lead

正解：A 解答を投票する

出題：7

A server administrator is deploying a VMware vSphere cluster and configuring High Availability on a PowerEdge MX7000 modular system.
Which configuration is required?

A. Enclosure-assigned storage

B. Drive-assigned storage

C. SAS IOM setup in redundant mode

D. PERC MX745P

正解：A 解答を投票する

出題：8

What item is used to refer to a daisy-chained configuration of a multiple MX7000 chassis environment?

A. Physical group

B. Wired group

C. Identity group

D. Chassis group

正解：B 解答を投票する

出題：9

When a SAS IOM is power cycled, how much time does it take for the storage-IOM to display mapping information?

A. 500 seconds

B. 400 seconds

C. 600 seconds

D. 300 seconds

正解：D 解答を投票する

出題：10

Which I/O module is supported for Fabric B?

A. MX5108n

B. MX5016s

C. MSG610s

D. MX5000s

正解：A 解答を投票する

D-PEMX-DY-23試験無料問題集「EMC Dell PowerEdge MX Modular Deploy 2023 認定」