CSSBB試験無料問題集（300題）「ASQ Six Sigma Black Belt Certification

出題：1

When a Belt properly analyzes the results of an experiment he must examine the Residuals in expectation of finding all of the following except _________.

A. All Residuals within 2 Standard Deviations of the Mean

B. Some Residuals lower than others

C. Some Residuals higher than others

D. Residuals will represent a Linear Regression

正解：D 解答を投票する

出題：2

Data that can be measured on a continuum and has meaningful decimal subdivisions are __________ data.

A. Variable

B. Discrete

C. Continuous

D. Surplus

正解：C 解答を投票する

出題：3

Following the completion of a LSS project the Belt not only creates a Control Plan he also develops a _____________ so those involved in the process know what to do when the critical metrics move out of spec.

A. Chain-of-Command

B. Response Plan

C. Call List

D. Defect Analysis Plan

正解：B 解答を投票する

出題：4

What aspects of Measurement Systems Analysis (MSA) studies are applicable when the process used to measure does not damage the part?

A. Destructive variable gage R&R and Crossed Study

B. Destructive variable gage R&R and Nested Study

C. Nondestructive variable gage R&R and Nested Study

D. Nondestructive variable gage R&R and Crossed Study

正解：C 解答を投票する

出題：5

On a _________________ a Belt screens variables, or various inputs, to analyze their relative impact on the output of concern.

A. Weighted Scale

B. X-Y Matrix

C. Poisson Chart

D. Multi-Vari Chart

正解：D 解答を投票する

出題：6

If you can Poka-Yoke a defect out of the process entirely then you do not need use SPC on the characteristic of interest in the defect.

A. True

B. False

正解：A 解答を投票する

出題：7

Which Experimental Design typically is most associated with the fewest number of input variables or factors in the design?

A. Fractional Factorial design

B. Simple Linear Regression

C. Full Factorial design

D. Response Surface Design

正解：D 解答を投票する

出題：8

For the data shown here which statement(s) are true? (Note: There are 2 correct answers).

A. With greater than 95% confidence, we conclude the samples are from Non-normal Distributions.

B. If we wanted to compare the Central Tendencies of these three samples we could use Mood's Median test.

C. With 95% confidence, we cannot conclude if the samples are from three Normal Distributions.

D. If we wanted to compare the Central Tendencies of these three samples we would use the one way ANOVA test.

正解：A,B 解答を投票する

出題：9

A fundamental rule is that both Standard Deviation and Variance can be added.

A. True

B. False

正解：B 解答を投票する

出題：10

Each of the items listed would impact the Process Capability for a process with a continuous output except ___________________.

A. Process Technology

B. Seasonal variation in process

C. Process Standard Deviation

D. Shape of process data distribution (e.g. Normal Distribution)

正解：A 解答を投票する

出題：11

Which statement is NOT correct about the Fitted Line Plot shown here?

A. If the reactant was 10 units, with 95% confidence we would expect a minimum yield of 148 units

B. With at least 95% confidence, we can expect less than 10 units of Yield when the reactant is at a value of 1

C. The independent variable is the reactant

D. When the reactant increases, the expected yield would increase

E. A reactant value between 6 and 8 units yields around 40 to 60

正解：E 解答を投票する

出題：12

"A calculated time frame that matches customer demand" is a definition of what Lean Principles term?

A. Kanban

B. Value Stream

C. Takt time

D. Kaizen event

正解：C 解答を投票する

出題：13

Which statement(s) are correct about the Factorial Plot shown here? (Note: There are 3 correct answers).

A. These plots are an example of interaction plots

B. When the cutting speed increased from low to high level, the tool age increases

C. These plots prove a statistically significance factor with 95% confidence

D. The coefficient of the metal hardness is positively related to the output of tool age

E. The coded coefficient is lower for cutting speed than the cutting angle related to the output of tool age

正解：B,D,E 解答を投票する

出題：14

If an experiment has 5 factors and no replicates for a 2-level Experimental Design with 16 experimental runs which statement is incorrect?

A. The experiment has 8 experimental runs with the first factor at the high level

B. The Main Effects are confounded with only 4-way interactions

C. The Main Effects for the 5 factors are not aliased or confounded but the 2-way interactions are confounded with the 3-way interactions

D. The Experimental Design is half-fractional

正解：C 解答を投票する

出題：15

When the Inputs, X's, for your process are Normally Distributed about the Mean, the Outputs, Y's, will always be Normally Distributed.

A. True

B. False

正解：B 解答を投票する

出題：16

When analyzing the behavior of our process to assess customer satisfaction we are concerned about both the variation such that it stays within the spec limits and how well the Mean is __________________ the process requirements.

A. Balanced against

B. Twice as great as

C. Centered relative to

D. Over and above

正解：C 解答を投票する

出題：17

Sally and Sara sell flower pots at their garage sale. Sally motivates Sara mentioning that they will sell a minimum of 22 pots per day if the outside temperature exceeds 60o F.
From a sample, whose population is assumed to follow a Normal Distribution, taken for 30 days at 60 degrees or more an average of 18.2 pots per day were sold with a Standard Deviation of 0.9 pots. What is the Z value for this sales process?

A. 2.11

B. 1.62

C. 4.22

D. 1.23

正解：C 解答を投票する

出題：18

The _______ is the most frequently occurring value in a distribution of data.

A. Mean

B. Center Point

C. Median

D. Mode

正解：D 解答を投票する

出題：19

Which of these graphs demonstrates conditions which would be sufficient to enable OCAP for the process?

A. Both

B. Xbar Chart

C. Neither

D. Time Series Chart

正解：B 解答を投票する

CSSBB試験無料問題集「ASQ Six Sigma Black Belt Certification - CSSBB 認定」