300-110試験無料問題集（96題）「Cisco Designing Cisco Wireless Networks 認定」

出題：1

A wireless engineer must design a WLAN for a university that requires outdoor Wi-Fi access. Which obstruction has the greatest effect on wireless signal propagation?

A. poles

B. wind

C. trees

D. rain

正解：C 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：2

An engineer is designing a wireless solution for a corporate campus which includes two primary buildings:
Research and Operations. The design must ensure seamless mobility for employees moving between buildings, support uninterrupted connectivity for real-time applications, and facilitate efficient Layer 2 and Layer 3 roaming. Each building ' s 9800-80 WLC manages its local APs, and the solution must support 802.11 r/k/v while maintaining an effective mobility control plane. Which design approach leverages Cisco mobility group architecture to meet the requirements?

A. Add both 9800-80 WLCs in a single mobility group with no specific roles assigned, enabling peer-to- peer coordination for seamless roaming across buildings.

B. Assign each 9800-80 WLC to separate mobility groups, one for each building, to isolate traffic and mitigate the risk of overloading a single mobility group.

C. Establish the Operations building ' s WLC as an anchor controller, configuring the Research building ' s WLC to tunnel all client traffic to it for centralized traffic management.

D. Designate the Research building ' s WLC as the primary controller and the Operations building ' s WLC as a secondary controller within a single mobility group to centralize mobility management.

正解：A 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：3

A customer has two Cisco wireless controllers named WLC-A and WLC-B. Each controller is in a different building on a campus. The WLCs have different Layer 3 interfaces and broadcast the same SSIDs from their respective APs. Users must remain connected to the same VLAN and maintain their IP addresses during roaming from the APs attached to WLC-A and WLC-B. Which action accomplishes the requirement?

A. Create an SSO cluster to ensure that client sessions sync between WLCs.

B. Enable 802.11r on each SSID on both WLCs to allow caching of the PMK.

C. Enable AP groups using the same name on both WLCs for each group.

D. Create a mobility group between the two WLCs to allow auto-anchoring.

正解：D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：4

A wireless network consists of two IOS XE controllers installed in a data center, 9100 series APs, and a corporate and a guest WLAN. The customer must have a high availability pair of two Cisco WLCs for the client SSO. Which two design approaches must the engineer take to meet the requirement? (Choose two.)

A. Both WLCs must have the same redundancy management IP address.

B. The controllers must run the same operating system version.

C. The controllers must have the same number of licenses.

D. Both WLCs must have the same service port IP address.

E. Each WLC must have a unique redundancy management IP address.

正解：B,E 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：5

How are mobility groups created, excluding mobility anchors?

A. If WLCs with HA SSO are deployed, each WLC in the WLC HA pair is considered separately as a mobility peer.

B. Each WLC must use the same mobility domain name and be defined as a peer in each other ' s static mobility members list.

C. A mobility group does not require all WLCs in the group to use the same virtual IP address.

D. The WLCs do not have to be of the same model or type to be a member of a mobility group, however each member should be running different software versions.

正解：B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：6

An engineer must perform a predictive design for a wireless network. The customer has devices that can tolerate at most 100 ms of delay when roaming. Which design criteria must be used?

A. voice

B. location

C. video

D. data

正解：A 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：7

An engineer is estimating the loss between two floors of an office building. Using Ekahau, they have measured -45 dBm at the ground level of the floor with the access point and -50 dBm at the ceiling level of the floor below it. Which value is the loss of the floor?

A. 95 dB

B. -5 dB

C. -95 dB

D. 5 dB

正解：D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：8

A network engineer is configuring high availability on an access point. What is the maximum number of controllers that can be configured?

A. 2

B. 1

C. 4

D. 3

正解：D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：9

A customer designs a Cisco wireless environment to provide connectivity to employees and guests. The guest SSID must be configured on three anchor WLCs named Anchor1, Anchor2, and Anchor3 in a DMZ. The guest anchor priority must be configured to ensure that Anchor1 has the highest priority. Which priority level must be incorporated in the design for Anchor1?

A. 2

B. 1

C. 0

D. 3

正解：B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：10

A wireless engineer is getting ready to perform a predictive site survey. The new network needs to support data and voice over wireless. Which two Cisco recommendations should be considered for the design?
(Choose two.)

A. Use the 5 GHz radio band due to 40 MHz bandwidth capability.

B. Set the cell overlap to 15%

C. Set the cell boundary to -67 dBm.

D. Use the 5 GHz radio band due to the 24 non-overlapping channels.

E. Set -19 dBm of separation between APs on the same channel.

正解：A,C 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

300-110試験無料問題集「Cisco Designing Cisco Wireless Networks 認定」