DC0-200試験無料問題集（120題）「Dell Certified Server Professional 認定」

出題：1

The system administrator notices the Dell badge on the front of the server is flashing orange on the PowerEdge 2650. What utility should the system administrator load to determine the cause of the flashing diagnostic indicator?

A. Dell Server Assistant

B. Dell Client Configuration Utility

C. OpenManage Array Manager

D. OpenManage Server Administrator

正解：D 解答を投票する

出題：2

What should you do before removing or reseating the RAID memory?

A. disconnect the RAID battery

B. disconnect the RAID key

C. disconnect the RAID cable

D. remove the hard drives

正解：A 解答を投票する

出題：3

You are configuring multiple servers in a rack-dense environment and need the ability to easily control all of the servers from one management station within the rack. Wh ich Dell racking component make s this possible?

A. PowerConnect switch

B. console switch

C. terminal emulator

D. flat panel monitor

正解：B 解答を投票する

出題：4

You are configuring network teaming on a PowerEdge server. The server has Windows 2000 installed and you do not know what network adapters are in the system. Without physically opening the chassis, what are two ways to see which network adapters are installed using the operating system? (Choose two.)

A. right-click Network Neighborhood, select Properties, double-click Internet Protocol (TCP/IP), and view protocol-bound adapters

B. type ipconfig /all at the command prompt; on the description line, the manufacturer and device type will be named

C. right-click My Computer, select Manage, left-click Device Manager, expand Network Adapters, and view installed adapters

D. type ifconfig -a at a command prompt; on the description line, the manufacturer and device type will be named

正解：B,C 解答を投票する

出題：5

What is required to enable a management application such as Dell OpenManage IT Assistant to receive SNMP traps from Dell OpenManage Server Agent/Server Administrator?

A. You configure the SNMP service on the computer on which OpenManage IT Assistant is running (the management station) to the correct read community name so that it can read the traps correctly .

B. You make sure OpenManage IT Assistant has discovered the managed node running Dell OpenManage Server Administrator.

C. Nothing needs to be done. OpenManage IT Assistant automatically registers to receive traps when it discovers the managed node on which Dell OpenManage Server Administrator is running.

D. You configure the SNMP service trap destinations on the computer on which Dell OpenManage Server Administrator is running to send traps to the management station (where OpenManage IT Assistant is running).

正解：D 解答を投票する

出題：6

Why is memory interleaving used?

A. to provide redundancy by allowing defective memory to be disabled

B. to provide speed improvements by allowing addressing to be set for the next access to the same DIMM, while data are being read from the previous access

C. to provide speed improvements by accessing memory in parallel

D. to provide redundancy by maintaining parity information on the DRAM to detect and correct single bit errors

正解：C 解答を投票する

出題：7

You received an e-mail that states that a server has a warning on Fan 1. How can you determine the server status using Server Administrator? (Choose two.)

A. using OMSA, from the system tree find the fan that displays an exclamation point

B. using the Server Console, drill down to the fan to display the states

C. using telnet , log into the server and enter the status command to display the fan states

D. use an OMSA CLI command to display the status of Fan 1

正解：A,D 解答を投票する

出題：8

What is the intended mounting location for a 0U rack mount device in a Dell rack?

A. at the top of the rack

B. in the mounting holes in the side walls of the rack

C. on the back doors of the rack

D. in any of the 42U spaces available

正解：B 解答を投票する

出題：9

What should you do to clear NVRAM and force the system to reset its configuration data?

A. press F10 when prompted at startup

B. boot to the Dell Server Assistant CD first

C. NVRAM cannot be cleared once it has been set by an administrator.

D. in the System Setup utility, activate the Num Lock, Caps Lock, and Scroll Lock lights on the keyboard, then press Alt-E

正解：D 解答を投票する

出題：10

Which keystroke is used to designate a single disk as a Hot Spare drive in the LSI Logic PERC controller?

A. <F4>

B. <F10>

C. <Insert>

D. <Space Bar>

正解：A 解答を投票する

DC0-200試験無料問題集「Dell Certified Server Professional 認定」