D-PE-FN-23試験無料問題集（238題）「EMC Dell PowerEdge Foundations 2023 認定」

出題：1

Which type of addressing does UEFI boot mode use?

A. Virtual

B. 128 bit.

C. 64 bit

D. 512 byte

正解：B 解答を投票する

出題：2

How can an administrator determine if a Dell EMC PowerEdge server component is hot-swappable?

A. Component is on the "HOT SWAP" list available from the LCD front panel

B. Words "HOT SWAP" are printed on the assembly of the component

C. Presence of a blue tab on the component

D. Presence of an orange tab on the component

正解：D 解答を投票する

出題：3

Which RAID level introduces a new state called "partially degraded" when a single drive failure occurs?

A. RAID 0

B. RAID 1

C. RAID 5

D. RAID 6

正解：D 解答を投票する

出題：4

An administrator is tasked with maximizing the processing power of a Dell EMC PowerEdge system.
What should the administrator consider doing?

A. Increase the CPU core count

B. Add more network ports

C. Use larger CPU sockets

D. Overclock the system

正解：A 解答を投票する

出題：5

An administrator receives simultaneous thermal alerts from multiple servers.
What should be checked first?

A. The computer room HVAC system

B. The firmware versions of the servers

C. The DHCP and DNS servers

D. The utilization of the server CPU

正解：A 解答を投票する

出題：6

What is the correct order of steps to configure a Dell PowerEdge server for HTTP boot in UEFI mode?
Note: Answers to this question are not verified by our experts, please study yourself and select the appropriate answers.

A. a) Select HTTP Device Settings.
b) Boot into F2 System Setup.
c) Select UEFI for Boot Mode.
d) Select System BIOS and Boot Settings.
e) Select System BIOS and Network Settings.
f) Select Finish and Reboot Server into System Setup.

B. a) Select UEFI for Boot Mode.
b) Select Finish and Reboot Server into System Setup.
c) Boot into F2 System Setup.
d) Select HTTP Device Settings.
e) Select System BIOS and Network Settings.
f) Select System BIOS and Boot Settings.

C. a) Select UEFI for Boot Mode.
b) Select HTTP Device Settings.
c) Boot into F2 System Setup.
d) Select System BIOS and Boot Settings.
e) Select System BIOS and Network Settings.
f) Select Finish and Reboot Server into System Setup.

D. a) Select HTTP Device Settings.
b) Select System BIOS and Network Settings.
c) Boot into F2 System Setup.
d) Select System BIOS and Boot Settings.
e) Select UEFI for Boot Mode.
f) Select Finish and Reboot Server into System Setup.

E. a) Select System BIOS and Network Settings.
b) Select UEFI for Boot Mode.
c) Boot into F2 System Setup.
d) Select System BIOS and Boot Settings.
e) Select HTTP Device Settings.
f) Select Finish and Reboot Server into System Setup.

F. a) Select HTTP Device Settings.
b) Select System BIOS and Boot Settings.
c) Select UEFI for Boot Mode.
d) Boot into F2 System Setup.
e) Select System BIOS and Network Settings.
f) Select Finish and Reboot Server into System Setup.

正解：C 解答を投票する

出題：7

A customer requires servers that focus on delivering tailored solutions that are rapidly shifting toward remote-based architectures.
Which type of servers provide this?

A. Accelerated Servers

B. Modular Servers

C. Cloud Servers

D. Data Center Scalable Solution Servers

正解：D 解答を投票する

出題：8

What is the maximum amount of hard drives required per RAID set, when configuring RAID 50?

A. 2

B. 4

C. 5

D. 3

正解：D 解答を投票する

出題：9

Which partition scheme is utilized by a BIOS implementation?

A. MBR

B. GPT

C. EBR

D. GRUB

正解：A 解答を投票する

出題：10

Which service is provided by a Dell EMC Smart Uninterruptible Power Supply (UPS)?

A. Increased wattage to the power supplies of the server

B. Limited standby power in the event of a power outage

C. Remote maintenance of any attached server

D. Uninterrupted power during a prolonged power outage

正解：B 解答を投票する

出題：11

Which technical concept does Disk Mirroring use?

A. Calculation of data from at least two disks that is stored on another disk

B. Division of data into blocks and spreading the data across hard drives

C. Duplication of data across separate hard drives

D. Duplication of system components for backup in case of failure

正解：C 解答を投票する

出題：12

What is the correct sequence of steps to gather a SupportAssist Collection via the iDRAC9 UI?
Note: Answers to this question are not verified by our experts, please study yourself and select the appropriate answers.

A. a) Navigate to SupportAssist.
b) Select Start a Collection.
c) Log in to the iDRAC.
d) Select Maintenance.
e) Click Collect.
f) Select destination where Collection will be saved.

B. a) Log in to the iDRAC.
b) Select Start a Collection.
c) Navigate to SupportAssist.
d) Select Maintenance.
e) Click Collect.
f) Select destination where Collection will be saved.

C. a) Select Maintenance.
b) Select destination where Collection will be saved.
c) Navigate to SupportAssist.
d) Log in to the iDRAC.
e) Click Collect.
f) Select Start a Collection.

D. a) Select Start a Collection.
b) Click Collect.
c) Navigate to SupportAssist.
d) Select Maintenance.
e) Log in to the iDRAC.
f) Select destination where Collection will be saved.

E. a) Select destination where Collection will be saved.
b) Navigate to SupportAssist.
c) Log in to the iDRAC.
d) Select Maintenance.
e) Click Collect.
f) Select Start a Collection.

F. a) Select Start a Collection.
b) Log in to the iDRAC.
c) Select Maintenance.
d) Navigate to SupportAssist.
e) Click Collect.
f) Select destination where Collection will be saved.

正解：B 解答を投票する

D-PE-FN-23試験無料問題集「EMC Dell PowerEdge Foundations 2023 認定」