DES-4121試験無料問題集（60題）「EMC Specialist - Implementation Engineer, PowerEdge 認定」

出題：1

A technician wants to move memory from a few older systems. What is the most efficient method to accomplish this task?

A. Power down all the older servers to physically check the memory
Move any matching memory to the new server

B. Use iDRAC to view the memory details of the older systems
Power down the servers to move matching memory to the new server

C. Power down any of the older servers to move any memory lo the new server Update BIOS to allow mismatched memory

D. Back up the server profile on the older server
Hove the matching memory and import the server profile to the new server

正解：C 解答を投票する

出題：2

A server has six memory modules attached to each CPU Memory Optimizer mode is configured The user now wants to have maximum protection tor the memory but cannot afford to lose any memory space What should the technician install / configure?

A. No additional memory
Switch on Single Rank Spare Mode

B. No additional memory
Switch to memory Mirroring

C. Six additional memory modules matching the original
Switch to Memory Mirroring

D. Six additional memory modules matching the original
Switch on Single Rank Spare Mode

正解：D 解答を投票する

出題：3

A user has a fully configured PowerEdge R640 and an iSM installed on their Windows.
2016 operating system. They now want to install OMSA to enable them to have alerts sent out In-Band to a management console.
What does the user need to consider?

A. iSM must be disabled before OMSA can be installed

B. OMSA can be installed on the same operating system with ISM. Provided both OMSA have iSM have the same firmware version revisions

C. iSM must be uninstalled before OMSA is installed

D. OMSA can be installed on the same operating system with iSM without restrictions

正解：D 解答を投票する

出題：4

A server has two power supply unites (PSUs) m a redundant configuration. One PSU fails.
A technician replaces the failed PSU, but the server does not return to redundant power mode.
What is the cause of this issue?

A. Power redundant option is disabled in the System Setup Utility

B. Server has not been power cycled to bring the now PSU online

C. Now PSU has a different wattage than the existing PSU

D. Both PSUs were not replaced at the same lime

正解：B 解答を投票する

出題：5

A technician is configuring a PowerEdge R640 that has two PSUs. The tack in which it is being installed has two power distribution units (POUs) No high power such as GPUs are required The user wants as much redundancy protection as possible.
What is the best way to configure the PSUs?

A. Redundancy Mode set to 1 + 1 with each PSU power cord connected to a different PDU

B. Redundancy Mode sot to 2+0 with each PSU power cord connected to a different POU

C. Redundancy Mode set lo l + 0 with the second PSU stored nearby tor Quick replacement if the first PSU fails

D. Redundancy Mode sot to 1 + 1 with both PSU power cords connected to the same PDU

正解：B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：6

A technician needs to remotely update the iDRAC with Lifecycle Controller firmware. They have downloaded the latest iDRAC firmware to the management station and connected to the iDRAC GUI.
What slop is required to complete the update?

A. Go to Summery Pago and reset the ORAC

B. Go to the Firmware Update pad and upload the iDRAC firmware

C. Boot the server into F 10 to start the firmware update

D. After firmware update completes, restart server

正解：A 解答を投票する

DES-4121試験無料問題集「EMC Specialist - Implementation Engineer, PowerEdge 認定」