NSE6_FSW-7.2試験無料問題集（57題）「Fortinet NSE 6

出題：1

Refer to the exhibits

Traffic arriving on port2 on FortiSwitch is tagged with VLAN ID 10 and destined for PC1 connected on port1. PC1 expects to receive traffic untagged from port1 on FortiSwitch.
Which two configurations can you perform on FortiSwitch to ensure PC1 receives untagged traffic on port1? (Choose two.)

A. Remove VLAN 10 from the allowed VLANs and add it to untagged VLANs on port1.

B. Enable Private VLAN on VLAN 10 and add VLAN 20 as an isolated VLAN.

C. Add the MAC address of PCI as a member of VLAN 10.

D. Add VLAN ID 10 as a member of the untagged VLANs on port1.

正解：C,D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：2

An administrator needs to deploy managed FortiSwitch devices in a remote location where multiple VLANs must be utilized to segment devices. No Layer 3 switch or router is present. The the only WAN connectivity is the router provided by the ISP connected to the public internet.
Which two items will the administrator need to use? (Choose two.)

A. FortiSwitch devices configured with NAT disabled.

B. FortiSwitch devices that have the required internal hardware for this configuration.

C. FortiSwitch and FortiGate devices configured with IPsec interfaces.

D. FortiSwitch and FortiGate devices configured with VXLAN interfaces.

E. A FortiSwitch interface connected to the ISP router configured with fortilink-13-mode enabled.

正解：A,E 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：3

Refer to the exhibit.

The exhibit shows the current status of the ports on the managed FortiSwitch. Access-1.
Why would FortiGate display a serial number in the Native VLAN column associated with the port23 entry?

A. A standalone switch with the shown serial number is connected on port23.

B. Ports connected to adjacent FortiSwitch devices show their serial number as the native VLAN.

C. port23 is a member of a trunk that uses the Access-1 FortiSwitch serial number as the name of the trunk.

D. port23 is configured as the dedicated management interface.

正解：A 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：4

What are two reasons why time synchronization between FortiGate and its managed FortiSwitch is critical in switch management? (Choose two.)

A. FortiSwitch will not allow other FortiSwitch devices in the chain be discovered by FortiGate.

B. FortiSwitch will not be able to become an NTP server for downstream devices.

C. FortiSwitch does not retain its time after a reboot, which gets reset after each reboot.

D. FortiSwitch cannot complete the DTLS handshake used in the CAPWAP tunnel.

正解：C,D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：5

Exhibit.

Two routes are not installed in the forwarding information base (FIB) as shown in the exnibit. Which two statements about these two route entries are true? (Choose two.)

A. These two routes have a higher administrative distance value available to the destination networks.

B. These two routes will be used as load-balancing routes.

C. These two routes will become primary, if the best routes are removed.

D. These two routes are available in the hardware routing table.

正解：A,C 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：6

Refer to the exhibit.

What two conclusions can be made regarding DHCP snooping configuration? (Choose two.)

A. Global configuration for DHCP snooping is set to forward DHCP client requests on all ports in the VLAN.

B. Maximum value to accept clients DHCP request is configured as per DHCP server range.

C. FortiSwitch is configured to trust DHCP replies coming on FortiLink interface.

D. DHCP clients that are trusted by DHCP snooping configured is only one.

正解：A,C 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

NSE6_FSW-7.2試験無料問題集「Fortinet NSE 6 - FortiSwitch 7.2 認定」