NSE6_SDW_AD-7.6試験無料問題集（121題）「Fortinet NSE 6 - SD-WAN 7.6 Enterprise Administrator 認定」

出題：1

When a customer delegate the installation and management of its SD-WAN infrastructure to an MSSP, the MSSP usually keeps the hub within its infrastructure for ease of management and to share costly resources.
In which two situations will the MSSP install the hub in customer premises? (Choose two.)

A. The customer requires SIA with centralized breakout.

B. The administrator expects a large volume of traffic between the branches.

C. The customer expects a large amount of VoIP traffic.

D. The majority of the branch traffic is directed to a corporate data center.

正解：A,D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：2

Refer to the exhibit. The administrator configured the SD-WAN rule ID 4 with two members (port1 and port2) and strategy lowest cost (SLA).
What are the two characteristics of the session shown in the exhibit? (Choose two.)

A. FortiGate will never re-evaluate this session.

B. FortiGate steered this flow according to the application detected and the outgoing interface is port3.

C. FortiGate steered this flow according to an SD-WAN rule.

D. FortiGate will re-evaluate this session if the outgoing interface goes down.

正解：C,D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：3

You have a FortiGate configuration with three user-defined SD-WAN zones and two members in each of these zones. One SD-WAN member is no longer in use in health-check and SD-WAN rules. You want to delete it.
What happens if you delete the SD-WAN member from the FortiGate GUI?

A. FodiGate accepts the deletion and removes routes as required.

B. FortiGate displays an error message. SD-WAN zones must contain at least two members

C. FortiGate accepts the deletion and places the member in the default SD-WAN zone.

D. FortiGate displays an error message. You must use the CLI to delete an SD-WAN member.

正解：A 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：4

Your FortiGate is in production. To optimize WAN link use and improve redundancy, you enable and configure SD-WAN.
What must you do as part of this configuration update process?

A. Replace references to interfaces used as SD-WAN members in the firewall policies.

B. Purchase and install the SD-WAN license, and reboot the FortiGate device.

C. Replace references to interfaces used as SD-WAN members in the routing configuration.

D. Disable the interface that you want to use as an SD-WAN member.

正解：A 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：5

Refer to the exhibits.
You use FortiManager to configure SD-WAN on three branch devices.

When you install the device settings, FortiManager prompts you with the error "Copy Failed" for the device branch1_fgt. When you click the log button, FortiManager displays the message shown in the exhibit.
There are two different ways to resolve this issue. Based on the exhibits, which methods could you use? (Choose two.)

A. Specify the gateway of the SD-WAN member port1 with an IP address or use the default value.

B. Review the per-device mapping configuration for metadata variables

C. Update the management IP address of branch1_fgt.

D. Do not define installation targets for SD-WAN members.

正解：A,B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：6

Refer to the exhibits.

You use FortiManager to configure SD-WAN on three branch devices.
When you install the device settings, FortiManager prompts you with the error "Copy Failed" for the device branch1_fgt. When you click the log button, FortiManager displays the message shown in the exhibit.
Based on the exhibits, which statement best describes the issue and how you can resolve it?

A. Check the connection between branch1_fgt and FortiManager.

B. Gateways for all members in a zone must be defined the same way. Specify the gateway of the SD-WAN member port1 without metadata variables.

C. Remove the installation target for the SD-WAN member port4. You cannot combine metadata variable and installation targets.

D. Check the metadata variable definitions, and review the per-device mapping configuration.

正解：D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：7

You are configuring SD-WAN to load balance network traffic and you want to take into account the link quality. Which two facts should you consider? (Choose two.)

A. You can select the lowest cost service level agreement (SLA) strategy and allow SD-WAN load balancing.

B. You can select the best quality strategy and allow SD-WAN load balancing.

C. The best quality strategy supports only the round-robin hash mode.

D. When applicable, FortiGate load balances the traffic through all members that meet the SLA target.

正解：B,D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：8

Refer to the exhibits.

You use FortiManager to configure SD-WAN on three branch devices.
When you install the device settings, FortiManager prompts you with the error "Copy Failed" for the device branch1_fgt. When you click Log, FortiManager displays the message shown in the exhibit.
Based on the exhibits, which statement best describes the root cause of the issue?

A. Gateways for all members in a zone must be of the same type.

B. The metadata variable definitions are incomplete or incorrect.

C. The connection between branch1_fgt and FortiManager failed.

D. You cannot combine metadata variables and installation targets.

正解：B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：9

Refer to the exhibit.
An SD-WAN zone configuration on the FortiGate GUI is shown.

What can you conclude about the zone and member configuration on this device?

A. You can delete the WAN1 zone.

B. You can add the member B-125 to the WAN3 zone and keep it as a member of the Test zone.

C. You can delete the virtual-wan-link zone.

D. The WAN2 zone contains no member.

正解：D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：10

Refer to the exhibits. The exhibits show the SD-WAN zone configuration of an SD-WAN template prepared on FortiManager and the policy package configuration.
When the administrator tries to install the configuration changes, FortiManager fails to commit.
What should the administrator do to fix the issue?

A. Configure both HUB1-VPN1 and HUB1-VPN2 as the destination of policy 3.

B. Configure HUB1 as the destination of policy 3.

C. Configure branch1_fgt as the installation target for policy 3.

D. Configure a normalized interface for the IPsec tunnel HUB1-VPN1.

正解：B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

NSE6_SDW_AD-7.6試験無料問題集「Fortinet NSE 6 - SD-WAN 7.6 Enterprise Administrator 認定」