GB0-372-ENU試験無料問題集「H3CSE-RS-SW 認定」

A. After the priority is adjusted, SWA will still send configuration BPDUs with itself as the root.

B. By default, the topology will converge again after 30 seconds.

C. After the configuration BPDU saved locally by SWB ages, it will send a configuration BPDU with itself as the root to SWA.

D. After receiving the low-priority configuration BPDU, SWC will immediately respond with the configuration BPDU with itself as the root.

A. It is not possible to add sub-ring 2 and sub-ring 3 to the same ring group.

B. If sub-ring 2 and sub-ring 3 are added to the same ring group, the ring groups should be configured on the switches SWB, SWC, SWE, and SWF respectively and the configurations should be consistent.

C. If sub-ring 2 and sub-ring 3 are added to the same ring group, the primary ring links corresponding to the edge nodes and auxiliary edge nodes of sub-ring 2 and sub-ring 3 in the ring group should be consistent.

D. If sub-ring 2 and sub-ring 3 are added to the same ring group, the edge nodes and auxiliary edge nodes of sub-ring 2 and sub-ring 3 in the ring group can be different

A. The bridge priority value step is 4096

B. The bridge priority is 16 bits in total, ranging from 0 to 65535.

C. The smaller the priority value, the lower the priority of the bridge.

D. If the switch is not configured with a bridge priority, the default value is 32768

A. MIB is stored in SM tree structure

B. The network management workstation can only access objects stored in the MIB on the managed device.

C. MIB is a collection of managed objects and is stored on managed devices

D. MIB is a collection of managed objects and is stored on the network management workstation

E. The network management workstation can only access objects stored in the MIB on the network management workstation.

A. MSTP switches and RSTP switches can belong to the same MST region

B. The MSTP switch will regard the RSTP switch as an MSTP domain consisting of a single switch.

C. The RSTP switch will regard the MST region as a logical switch, and the bridge ID is the ID of the switch directly connected to the RSTP switch in the MST region.

D. The MSTP switch will parse the RSTBPDU into an MST BPDU, where IRPC is 0

A. BSR is responsible for collecting and publishing RP information in the PIM-SM domain

B. There can be only one BSR in a PIM-SM domain

C. RP in PIM-SM can be manually specified or dynamically elected.

D. BSR selects the best RP for each multicast group

A. By running this command on a port of an RSTP or MSTP switch, you can switch the spanning tree mode of the port to STP.

B. This command is used when RSTP switches and MSTP switches are interconnected.

C. This command is used when the switch port running RSTP or MSTP is connected to the STP device.

D. This command is used when switches from different manufacturers are interconnected and MSTP is running to check summary information.

A. After SWB completes the synchronization process, it will reply with an Agreement message to SWA, and its port E1/0/1 will immediately enter the forwarding state.

B. After receiving the Agreement message sent by SWB, SWA's port E1/0/1 will immediately enter the forwarding state.

C. The designated port of SWB will continue the P/A handshake process with the downstream switch

D. During the P/A process, no timer will be used, so the designated port can quickly enter the forwarding state, thereby achieving rapid network convergence.

A. The client should associate the key with the server to successfully complete the verification.

B. When enabling authentication, you must configure both the authentication key and the trusted key.
Otherwise, authentication cannot be started normally.

C. If the client does not enable authentication and the server enables authentication, the client's clock can also be synchronized

D. The authentication of the client and server must be consistent, otherwise the clock synchronization will fail.

A. If P1-2=P2-2, C1-2<C2-2, then RT2 wins.

B. If P1-2>P2-2, C1-1<C2-2, then RT2 wins.

C. If P1-1=P2-2, C1-1<C2-2, then RT1 wins.

D. If P1-2=P2-2, C1-2=C2-2, then RT2 wins.

E. If P1-1>P2-2, C1-1<C2-2, then RT1 wins.

F. If P1-1=P2-2, C1-1=C2-2, then RT1 wins.

A. The ARP entry learned on SWA is: IP Address MAC Address VLAN ID Interface Aging Type 10.1.1.1
0011-1111-11112 Eth1/0/1 20D 10.1.1.20022-2222-22223Eth 1/0/2 20D

B. None of the above is correct

C. The ARP entry learned on PCA is: Internet Address Physical Address Type 10.1.1.20022-2222-2222 dynamic

D. The ARP table entry learned on the PCB is: Internet Address Physical Address Type 10.1.1.100E0- FC0A-0010 dynamic

A. In the figure, by default, SWA port E1/0/1 needs to wait twice the Forward Delay time before it can enter the Forwarding state.

B. In MSTP, the downstream device will respond to the BPDU with the Agreement bit set only after receiving the BPDU with both the Proposal and Agreement bits set from the upstream device.

C. Both RSTP and MSTP require that the designated port of the upstream device can only perform rapid migration after receiving the Agreement message from the downstream device.

D. By configuring stp no-agreement-check on the port, the MSTP switch will not check whether the Agreement bit is set in the Proposal BPDU sent from the upstream.

A. RT2

B. RT1

C. RT3