HPE7-A08試験無料問題集（137題）「HPE Aruba Networking Switching Professional 認定」

出題：1

You are configuring OSPF on each of the devices shown. After verifying the OSPF neighbor table on each, you notice that Router-1 and Access-1 have neighbors in the 2WAY state. What is the reason for this?

A. This is normal behavior for OSPF neighbors on a broadcast network.

B. Router-1 and Access-1 have reached a tie in the DR election.

C. IGMP snooping has been configured on Router-1 and Access-1.

D. Router-1 and Access-1 have no OSPF networks to advertise.

正解：A 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：2

Refer to the exhibit:

Using the configuration below, you have configured OSPF at a small branch site, which only requires a single default route to reach the Internet and all other sites. When examining the routing table, you still see other OSPF routes besides the default route.
What OSPF area type should you configure?

A. Stub Area

B. Totally Stubby Area

C. Not-So-Stubby Area

D. Totally Not-So-Stubby Area

正解：B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：3

Your customer is concerned about users connecting unmanaged switches to the network and causing outages.
Which CX switch feature should you recommend?

A. Loop protection

B. MAC authentication

C. BPDU Guard

D. Port security

正解：A 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：4

TAC has made a configuration change on the CLI of a CX switch using aruba-central support-mode. Which statement about the switch configuration in HPE Aruba Networking Central is true?

A. Config auto-commit will be disabled and must be re-enabled manually.

B. The configuration change will be automatically synchronized to HPE Aruba Networking Central.

C. The user must make the same change in HPE Aruba Networking Central for synchronization to occur.

D. HPE Aruba Networking Central will automatically overwrite the configuration change.

正解：B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：5

A multicast configuration on an HPE Aruba Networking CX 6300 VSF is used for a group address 239.0.0.1.
The configuration is having issues, and the video streaming clients are not receiving the stream.
What would be a possible root cause for the problems experienced?

A. The IGMP is enabled on the VLANs without any multicast traffic.

B. The IGMP-snooping is using version 2 configured for the SVI.

C. The selected multicast address will overlay with PIM-SM discovery address.

D. The selected multicast address will overlay with Link-Local Multicast address scope.

正解：C 解答を投票する

出題：6

What should you configure for an interface connected to a device you cannot trust to assign DSCP markings?
(Select two.)

A. Configure " qos trust none "

B. Apply a dscp-map to the interface to assign a Local Priority value

C. Configure Weighted Fair Queuing

D. Apply a classifier-based policy to the interface to assign a Local Priority value

E. Configure " qos trust cos "

正解：A,D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：7

With the given output from an HPE Aruba Networking CX 6300:

Which statement about the output above is true?

A. The route-map with aspath-list intended for iBGP peers.

B. The defined route-map is used in BGP with neighbor remote-as export.

C. The accepted AS paths are defined in the aspath-list.

D. The advertised AS paths are configured in an IP prefix-list.

正解：C 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：8

You are implementing a directly connected routing plan using OSPF on an HPE Aruba Networking CX 6200 and ISP router. What would be the impact of changing the network type to point-to-point?

A. It will reduce the number of LSA type-2 advertisements

B. The configuration would remain as the default

C. A larger number of OSPF routes would be supported

D. It will increase the number of LSA type-3 advertisements

正解：A 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：9

OSPF peering is configured between HPE Aruba Networking CX 6300 switches utilizing BFD. You ' ve made this configuration on switch B, while switch A is in the default configuration:

Which BFD Tx/Rx interval values will switch A use for the show bfd session?

A. Switch A show BFD sessions using 500ms

B. Switch A show BFD sessions using 300ms

C. Switch A show BFD sessions using 2000ms

D. Switch A show BFD sessions using 6000ms

正解：B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

HPE7-A08試験無料問題集「HPE Aruba Networking Switching Professional 認定」