H12-831_V1.0-ENU試験無料問題集「Huawei HCIP-Datacom-Advanced Routing & Switching Technology V1.0 認定」

ページ: 1 / 16
トータル 158 問
完全版を入手する
On the IS-IS IPv6 network shown in the figure, multi-topology is enabled on all routers.
* The IPv6 address of Loopback0 on R4 is 2000::4/128.
* The command ipv6 summary 2000::/64 level-1-2 is configured in the IS-IS process of R4.

Which of the following statements is false?

解説: (GoShiken メンバーにのみ表示されます)
On the network shown in the figure, IS-IS runs on R1, R2, R4, and R5, and the area ID is 49.0001. IS-IS runs on R3 and R6, and the area ID is 49.0002. The import-route isis level-2 into level-1 command is configured on R2.
In AS 65000, R1, R3, R4, and R6 each establish iBGP peer relationships with R2 and R5. R2 and R5 are Route Reflectors (RRs), and R1, R4, R3, and R6 are clients.
An iBGP peer relationship is established between R2 and R5, and the same cluster ID is configured. The iBGP peer relationships are established using Loopback0. The IP address of Loopback0 on each router is 10.0.X.X/32, where X is the router number.
R1 and R4 import the external route 192.168.1.0/24 to BGP through the import-route command, and R3 and R6 import the external route 192.168.2.0/24 to BGP through the import-route command.

Which of the following statements are true?

正解：A,B,D 解答を投票する
解説: (GoShiken メンバーにのみ表示されます)
As shown in the figure, R1 to R4 are four routers in AS123. They all run OSPF to implement route reachability within the AS.
* Network segments 10.1.1.0/24 and 10.4.4.0/24 are not advertised into OSPF.
* R1 and R4 establish an IBGP peer relationship using Loopback0 and advertise network segments
10.1.1.0/24 and 10.4.4.0/24 into BGP.
Which of the following methods can be used to implement communication between PC1 and PC2?

Options:

解説: (GoShiken メンバーにのみ表示されます)
A network engineer enters dir on the device to obtain the following file names. Which is most likely to be the version file of the device?

There are multiple types of MAC address entries on a switch. Which of the following entries are manually configured and cannot be aged out?

A network engineer checks LLDP neighbor information on R1. The output is shown below.
Which of the following statements are true?
LLDP Output:
yaml
CopyEdit
<R1> display lldp neighbor interface GE0/0/0
------------------------------------------------
GE0/0/0 has 1 neighbor(s):
Neighbor index: 1
Chassis type: MAC Address
Chassis ID: faed-ad04-0010
Port ID subtype: Interface Name
Port ID: GE0/0/0
System name: R2
System description: Huawei YunShan OS
Version 1.22.01 (AR8000 V100R002C200)
Copyright (C) 2021-2022 Huawei Technologies Co., Ltd.
HUAWEI AR8140-12G10XG
System capabilities supported: bridge router
System capabilities enabled: bridge router
Management address type: IPv4
Management address: 192.168.1.1
Expired time: 107s

正解：A,B,C 解答を投票する
解説: (GoShiken メンバーにのみ表示されます)
In the figure, a network administrator configures a static LSP to implement MPLS data forwarding. The lower part of the topology shows the packet header information obtained from a device.
Which of the following statements are true?

Options:

解説: (GoShiken メンバーにのみ表示されます)
On the ISIS network shown in the figure, R1 imports a default route using the default-route-advertise always level-1 command. In this case, R3 can learn this default route through IS-IS.

To support the processing and calculation of IPv6 routes, IS-IS adds a new NLPID to TLV 129. The NLPID is an 8-bit field that identifies network layer protocol packets. Which of the following is the NLPID of IPv6?

Service routes of an enterprise are transmitted on the network. Some configurations of PE1 and PE2 are shown in the figure. Which of the following LSAs may CE2 receive?

ページ: 1 / 16
トータル 158 問