JN0-650試験無料問題集（124題）「Juniper Enterprise Routing and Switching, Professional (JNCIP-ENT) 認定」

出題：1

Click the Exhibit button.

Referring to the exhibit output, which statement is correct?

A. The device with an IP address of 192.168.100.2 is attached to VNI 5010.

B. The output shows the router ID of the device sending the EVPN Type 2 routes.

C. The output shows the route distinguisher of the device sending the EVPN Type 2 routes.

D. IP addresses 10.1.1.1 and 10.1.2.3 are connected to the same VNI.

正解：D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：2

Click the Exhibit button.

Referring to the exhibit, R2 receives a packet from the multicast source on its ge-0/0/4.0 interface.
Which two statements are correct in this scenario? (Choose two.)

A. R2 determines that the packet is coming in on an interface that is on the reverse path back to the source.

B. The packet is discarded.

C. R2 verifies the existing unicast routing table and determines that this interface is not on the reverse path back to the source.

D. All interfaces other than ge-0/0/4.0 will be on the outgoing interface list.

正解：B,C 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：3

Which two statements are correct about EVPN/VXLAN deployments? (Choose two.)

A. The VLAN tags are maintained when traffic is sent through the IP fabric.

B. The VLAN tags associated with source and destination ports for a given flow must match.

C. The VLAN tags are removed before traffic is sent through the IP fabric.

D. The VLAN tags associated with source and destination ports for a given flow are not required to match.

正解：C,D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：4

Click the Exhibit button.

You created a PVLAN between two EX Series switches and configured the ge-0/0/1 interface on both switches as trunk ports. You notice that traffic for community VLANs configured on both switches is not forwarded over the ge-0/0/1 trunk ports.
Referring to the exhibit, which action will solve this problem?

A. Configure the core-facing parameter for the ge-0/0/1 interface on both switches.

B. Configure the inter-switch-link parameter for the ge-0/0/1 interface on both switches.

C. Configure the vlan-auto-sense parameter for the ge-0/0/1 interface on both switches.

D. Configure the vlan-rewrite parameter for the ge-0/0/1 interface on both switches.

正解：B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：5

Click the Exhibit button.

After connecting a new Class 4 PoE device to your EX Series switch on port ge-0/0/2, users report that the device will not power on.
Referring to the exhibit, how would you solve this problem?

A. Configure class mode and confirm that the switch recognizes the device as Class 4.

B. Change the priority on the ge-0/0/2 interface to high.

C. Replace the switch with a model that supports PoE+ or migrate the new device to a switch that supports PoE+.

D. Update the configuration to allocate 30.0W of power budget to ge-0/0/2.

正解：C 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：6

You are asked to configure an 802.1X solution that supports dynamic VLAN assignment. In this scenario, which two modes support using vendor-specific attributes (VSAs)? (Choose two.)

A. multiple supplicant mode

B. static MAC bypass mode

C. single supplicant mode

D. single-secure supplicant mode

正解：A,C 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：7

Which two statements are correct about IPv4 multicast to Ethernet address mapping? (Choose two.)

A. ARP is used to resolve IPv4 multicast addresses to the corresponding multicast Ethernet addresses.

B. The first 23 bits of an IPv4 multicast address are used when mapping to the corresponding Ethernet address.

C. Multiple IPv4 multicast addresses can map to a single multicast Ethernet MAC.

D. Multicast Ethernet MAC addresses always start with 01:00:5E.

正解：C,D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：8

Click the Exhibit button.

Referring to the exhibit, you see that the 0.0.0.0/0 route is coming from AS 64512.
What is the command to achieve this task?

A. show route protocol bgp source-gateway <peer ip>

B. show route receive-protocol bgp <peer ip>

C. show route receive-protocol bgp <peer ip> hidden

D. show route protocol bgp next-hop <peer ip>

正解：C 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：9

Click the Exhibit button.

What is the OSPF router type shown in the exhibit for router 192.168.2.1?

A. an ASBR

B. an ABR

C. both an ABR and an ASBR

D. neither an ABR nor an ASBR

正解：D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：10

Click the Exhibit button.

You configured MVRP in your Layer 2 network using the configuration shown in the exhibit. You verified that the appropriate VLANs are configured and applied on the two access switches. You are using RSTP as your loop prevention mechanism. Unfortunately, the users are not able to communicate with their corresponding server attached to the Access-2 switch.
In this scenario, what should you do to solve this problem?

A. Configure VSTP instead of RSTP as your loop-prevention mechanism.

B. Configure the ge-0/0/16.0 interface on the Core-1 switch under MVRP.

C. Configure the access interfaces on the Access-2 switch under MVRP.

D. Configure the access interfaces on the Access-1 switch under MVRP.

正解：C 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

JN0-650試験無料問題集「Juniper Enterprise Routing and Switching, Professional (JNCIP-ENT) 認定」