FCP_FWF_AD-7.4試験無料問題集（169題）「Fortinet FCP - Secure Wireless LAN 7.4 Administrator 認定」

出題：1

Refer to the exhibits.
Exhibit A

Exhibit B

A wireless network has been created to support a group of users in a specific area of a building. The wireless network is configured but users are unable to connect to it. The exhibits show the relevant controller configuration for the APs and the wireless network. Which two configuration changes will resolve the issue? (Choose two.) Response:

A. For both interfaces in the wtp-profile, configure vap-all to be manual

B. For both interfaces in the wtp-profile, configure set vaps to be "Authors"

C. Increase the transmission power of the AP radio interfaces

D. Disable intra-vap-privacy for the Authors vap-wireless network

正解：A,B 解答を投票する

出題：2

Refer to the exhibit.

If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area? Response:

A. Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility

B. Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.

C. Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor

D. Areas with the signal strength weaker than -68 dB are cut out of the map

正解：B 解答を投票する

出題：3

Employees at the remote office reported speed issues with the wireless network. Dual-band FortiAP devices have been correctly deployed throughout the office to ensure coverage and optimal performance. However, employees have noticed that the wireless stations consistently connect to the 2.4 GHz network but not the 5 GHz network.
What must IT administrators perform to troubleshoot the issue?
Response:

A. Review if FortiAP resources are not experiencing high CPU or memory usage.

B. Verify that the allocated frequency channel on FortiAP is not exhausted.

C. Disable the 2.4 GHz radio to force the wireless stations to connect.

D. Confirm whether internet speed limits are preventing access to high speed by wireless stations.

正解：B 解答を投票する

出題：4

What actions can be taken using WIDS profiles in FortiGate?
(Select all that apply)
Response:

A. Managing SSID broadcast settings

B. Suppressing unauthorized access points

C. Enhancing wireless signal strength

D. Detecting rogue APs

正解：B,D 解答を投票する

出題：5

Which command is used to configure VLANs on an SSID using the FortiGate CLI?
Response:

A. config wireless-controller vap

B. config wireless-controller vlan

C. config wlan ssid

D. config interface vlan

正解：A 解答を投票する

出題：6

Which configuration is necessary to allow guest users access to a wireless network using the FortiGate guest management feature?
Response:

A. Set up advanced bridge mode options

B. Configure VLANs on SSIDs

C. Enable SSID hiding

D. Provision guest accounts

正解：D 解答を投票する

出題：7

Which statement is true about multiple pre-shared keys on a managed FortiAP?
Response:

A. MPSK profiles can be referenced in multiple SSIDs.

B. MPSK profiles can be enabled with a single pre-shared key on an SSI

C. MPSK profiles can be associated with specific firewall schedules.

D. MPSK profile groups can be linked to one MPSK profile.

正解：D 解答を投票する

出題：8

When configuring VLANs on SSIDs, what is the primary benefit?
Response:

A. Logical segregation of network traffic

B. Enhanced wireless signal strength

C. Simplified guest management

D. Improved load balancing

正解：A 解答を投票する

FCP_FWF_AD-7.4試験無料問題集「Fortinet FCP - Secure Wireless LAN 7.4 Administrator 認定」