H31-341-ENU試験無料問題集（215題）「Huawei HCIP-Transmission V2.0 認定」

出題：1

The following description of the signal flow of the OTM site (OSN 8800 device), which is wrong?

A. OSC receiving direction: Line-> FIU-> Sc2

B. Service transmission direction: SDH signals-> LSX->M40V-> OBU1-> FIU-> Line

C. Service transmission direction: SDH signals-> LSX-> M40V-> OBU1-> Line

D. Service receiving direction: Line->FIU-> OAU-> M40V-> LSX-> SDH signals

正解：D 解答を投票する

出題：2

Which of the following description of the Optix OSN 9800 sub-rack is correct? (Multiple choice)

A. When the OSN 9800 Universal Platform Sub-rack is used as a slave sub-rack, the main control board must be placed.

B. In the OSN 980 0U32 sub-rack, IU70 is the primary CTU and IU78 is the standby CTU.

C. The service board can be inserted into the IU18 slot only when the OSN 9800 P18 is used as the slave sub-rack.

D. The OSN 9800 U16 sub-rack has a total of 16 service slots. These slots have the same capacity and support up to 400 bit/s ODUk crossover in a single slot.

正解：C,D 解答を投票する

出題：3

Which of the following statement about the MPLS-TP OAM level is correct?

A. Tunnel is the service layer of PW, PW is the service layer of Service, and Service is the service layer of Section.

B. Section is the service layer of PW, PW is the service layer of Tunnel, and Tunnel is the service layer of Service.

C. Service is the service layer of the PW, PW is the service layer of the Tunnel, and Tunnel is the service layer of the Section.

D. Section is the service layer of the tunnel, Tunnel is the service layer of the PW, and PW is the service layer of the Service.

正解：D 解答を投票する

出題：4

Which of the following SOM systems is not monitored?

A. Light performance flatness

B. Receive OTU input optical power

C. Main light path performance

D. Type of originating FEC

正解：D 解答を投票する

出題：5

Which of the following boards can be inserted on the OSN 9800 U64 subrack?

A. TN54GS4

B. TNV1N401

C. TN18LSC

D. TNF 5UNQ2

正解：A 解答を投票する

出題：6

The NS4 board features test includes: (Multiple choice)

A. -20dB spectral width test

B. Receive sensitivity

C. Side mode suppression ratio

D. Center wavelength test

正解：A,B,C,D 解答を投票する

出題：7

Path method creates OCh failure, what are the possible reasons? (Multiple Choice)

A. Some pigtails are not connected

B. Inconsistent wavelength setting at both ends of source and sink

C. No service layer path

D. There are still unremoved alarms in the boards involved in OCh.

正解：A,B,C 解答を投票する

出題：8

What common methods for MSTP device fault location can be summarized as?

A. One board change, two loopbacks, three analysis.

B. One analysis, two loopbacks, three board change.

C. One loopbacks, two board change, three analysis.

D. One analysis, two board change, three loopbacks.

正解：B 解答を投票する

出題：9

For the nonlinear effect FWM, which of the following way is correct?

A. Control the incoming fiber power

B. Control the optical power of a single wavelength

C. Using large effective area fiber

D. Do not use G.653 fiber in DWDM systems

正解：B 解答を投票する

出題：10

Optical monitoring channel is used for monitoring of WDM optical transmission system. In the UU-T proposal, it is preferable to use a wavelength of 1510 nm at how much rate?

A. 576 kbit/s

B. 192 kbit/s

C. 2 Mbit/s

D. 64 kbit/s

正解：C 解答を投票する

出題：11

Which of the following description of the DM12 board are correct? (Multiple choice)

A. One DX1 board can be used with two DM12

B. Accessing G.703 64 kbit/s co-directional service signals through the DB44 interface on the DM12 board

C. Access the NX6bit/s and sub-rate service signals through the DB28 connector on the DM12 board.

D. Electrical signal input and output interfaces for DDN, Unframed E1 and sub-rate services

正解：A,B,C 解答を投票する

出題：12

Which of the following protections need to use the APS protocol? (Multiple Choice)

A. 1:1 optical line protection

B. SW SNCP protection

C. ODUk ring network protection

D. ODUk SNCP protection

正解：A,C 解答を投票する

出題：13

In the WDM networking design, as long as there are enough EDFA cascades to compensate for the loss of optical power during transmission. Then the system can transmit a long distance without restriction.

A. FALSE

B. TRUE

正解：A 解答を投票する

出題：14

The ways of synchronize alarms are (). (Multiple Choice)

A. Manual synchronization

B. Timing synchronization

C. Automatic synchronization

正解：A,C 解答を投票する

H31-341-ENU試験無料問題集「Huawei HCIP-Transmission V2.0 認定」