2025年最新のBICSI INSTC_V8問題集と試験テストエンジン [Q94-Q114]

2025年最新のGoShiken BICSI INSTC_V8問題集と試験テストエンジン

BICSI INSTC_V8問題集にはリアル試験問題解答

質問 # 94
Which of the following fire-ratings provides information about smoke leakage?

A. L rating
B. W rating
C. E rating
D. I rating

正解：A

質問 # 95
Regarding safety protocols from the BICSI Installer 2 manual, which is the MOST important initial step before using a power puller for cable installation?

A. Conducting a thorough job hazard analysis (JHA) or risk assessment
B. Verifying that all conduit runs are reamed and free of burrs
C. Wearing a full-body harness, regardless of the installation height
D. Ensuring the puller's label matches the cable category

正解：A

質問 # 96
Which type of tester includes a set of modular plugs?

A. Multimeter
B. Tone generator
C. Cable-end locator kit
D. Inductive amplifier

正解：C

質問 # 97
Which of the following types of construction protects the optical fiber by supporting each strand of glass with a buffer coating extruded over the base optical fiber's 250 um acrylate coating?

A. Loose tube
B. Ribbon
C. Tight buffered
D. Single stranded

正解：C

質問 # 98
When verifying polarity in a duplex fiber installation (e.g., LC to LC), which method is MOST commonly used to ensure correct transmitter-to-receiver alignment?

A. Checking the cable manufacturer's datasheet for polarity orientation
B. Use of color-coded connectors (blue for transmit, red for receive)
C. Light source and power meter, verifying signal from Tx on one end is received on Rx at the other
D. Visual inspection of the outer jacket color

正解：C

質問 # 99
Two truck drivers are communicating over a Citizens Band (CB) radio. Only one driver can send a message at a time with this system.
What type of transmission method is used in this example?

A. Full duplex
B. Simplex
C. Half-duplex

正解：C

質問 # 100
A purple backboard should be used to identify ________?

A. Horizontal cable
B. Demarcation point
C. Network connections
D. Common equipment

正解：D

質問 # 101
Which of the following is a measure of the amount of information being transported over media?

A. Megabits
B. Kilowatt hours
C. Volt-amperes
D. Megahertz

正解：A

質問 # 102
During a fiber optic cable installation, the cable manufacturer specifies a maximum tensile load of 2700 N (600 lb). What is the TYPICAL recommended maximum pulling tension you should not exceed for short pulls, to ensure safety margins?

A. 810 N (180 lb)
B. 2700 N (600 lb)
C. 1890 N (425 lb)
D. 1350 N (300 lb)

正解：D

質問 # 103
Which of the following fire ratings refers to the time period that a fire-rated assembly can resist flame passage?

A. W rating
B. T rating
C. L rating
D. F rating

正解：D

質問 # 104
Fall protection is required whenever a person is exposed to a fall hazard more than ____?

A. 1.2 m (4')
B. 1.83 m (6')
C. 3 m (10')
D. 2.4 m (8')

正解：B

質問 # 105
Which is a keyed, contact, moderate loss connector in present use today that is pull & wiggle-proof?

A. SMA 906
B. Subscriber Connector (SC)
C. Opti-Jack
D. Straight Tip (ST)

正解：D

質問 # 106
Which of the following is used to express system gain and loss?

A. Henries
B. Decibel (dB)
C. Farads
D. Ohms

正解：B

質問 # 107
When labeling patch panels, which of the following is MOST aligned with TIA-606 and BICSI best practices?

A. Only label the left-most and right-most ports
B. Use building zone references, omitting port identifiers
C. Label each port sequentially by row (e.g., 1-24, then 25-48, etc.)
D. Assign labels based on random color coding for each port

正解：C

質問 # 108
What is the MOST likely negative consequence of not maintaining proper cable slack in the TR (e.g., 3 m / 10 ft) as recommended by BICSI?

A. Inability to re-terminate or move cabling in the future
B. Increased crosstalk on the link
C. Violation of local electrical building codes
D. Blocking patch cord access in the rack

正解：A

質問 # 109
When routing conduits through a fire-rated floor assembly, which principle BEST ensures compliance with fire code requirements?

A. Installing a second parallel conduit for redundancy
B. Oversizing the conduit to reduce cable friction
C. Filling any gap around the conduit with an approved firestop system
D. Placing a service loop inside the conduit above the floor

正解：C

質問 # 110
What is the recommended thickness for plywood that will be mounted on the walls of a telecommunications room?

A. 32 mm (1-1/4")
B. 19 mm (3/4")
C. 25 mm (1")
D. 12.7 mm (1/2")

正解：B

質問 # 111
Which of the following is a critical requirement for a Telecommunications Enclosure (TE) as opposed to a Telecommunications Room (TR)?

A. The TE can be secured to a wall or ceiling and is typically smaller, without dedicated HVAC
B. The TE must hold all building cross-connects for the backbone cabling
C. The TE requires dedicated electrical power panels for distribution
D. The TE must have active electronics fully protected by a 2-hour rated firewall

正解：A

質問 # 112
What is the specified performance level for Category 6 cable?