[2025年07月] 検証済みAMPP Senior-Internal-Corrosion-Technologistリアル豪華お試しセット試験問題集でPDF
Senior-Internal-Corrosion-Technologist問題集PDF最新 [2025年最新] 究極の学習ガイド
質問 # 30
The cost of qualified Coating Inspection Is normally offset by:
- A. Lower Application Costs
- B. Lower Coating Life Cycle Costs
- C. Lower Supervision Costs
- D. Lower Safety Enforcement Costs
正解：B
質問 # 31
When conducting inspections the Inspector should follow which standards:
- A. The specified standards
- B. Australian standards in Australia
- C. ISO standards in Europe and Asia
- D. NACE and 55PC standards in North America
正解：A
質問 # 32
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide If and when a destructive test is required.
- A. True
- B. False
正解：B
質問 # 33
You ate the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no Individual gauge reading shall be below a certain value. As this is not part of the standard you should:
- A. Call your supervisor
- B. Request clarification from the specifier
- C. Ignore the additional requirement
- D. Enforce the additional requirement
正解：B
質問 # 34
The coating applicator has ignored a surface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Advise the Owner and write a Non-Conformance report
- B. Require the Applicator to remove the applied coating
- C. Stop the Job
- D. Ignore the situation
正解：A
質問 # 35
NACE International Standards are developed by:
- A. International mandates
- B. Government mandates
- C. Standard committees
- D. Regional mandates
正解：D
質問 # 36
When observing fabrication defects the NACE Inspector should:
- A. Write an NCR and call the fabricator
- B. Require they be corrected prior to coating
- C. Consult the specification to determine how they should be treated
- D. Stop the job immediately
正解：C
質問 # 37
You are the NACE Coating Inspector ona tank lining project where desiccant dehumidificationis being used.
Since the first shift ofabrasive Wasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Check to see if the dehumidification equipment is operating correctly
- C. Advise the coating applicator supervisor of your readings
- D. Document the readings at the end of the shift
正解：C
質問 # 38
Coating surveys may Include which steps? Select All That Apply:
- A. Develop a survey plan
- B. Summarize the collected data
- C. Evaluate the coatings performance
- D. Schedule the remedial work
正解：A、B
質問 # 39
You are theNACE Coating Inspector on a tank lining project and are asked to perform ahigh voltage holiday test after thecoating applicators have completed their final repairs. After meeting all the confined space entry permit you enter the tank and notice a very strong odor of solvent.
Your first course or action should be to:
- A. Exit the tank and document the incident in your dally report
- B. Exit the tank and Immediately and report the problem to the nearest safety supervisor
- C. Investigate to find the source of the odor
- D. Don your air supplied respirator and continue the testing
正解：B
質問 # 40
You can use magnifiers to examine all of the following EXCEPT
- A. Surface cleanliness
- B. Surface profile
- C. Blisters
- D. Mill scale
正解：A
質問 # 41
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate Inorganic zinc-rich primers by solvent rub requires
- A. 25 double rubs with a saturated cloth.
- B. 35 single rubs with a saturated cloth.
- C. 25 single rubs with a saturated cloth.
- D. 50 double rubs with a saturated cloth.
正解：D
質問 # 42
Thermal Spray coatings provide:
- A. Sacrificial protection
- B. Thermal protection
- C. inhibitiveprotection
- D. Barrier protection
正解：D
質問 # 43
When using a destructive Paint Inspection Gauge the NACE inspector must:
- A. Select the appropriate hand wheel based on the measured Dry Film Thickness prior to use
- B. Ensure the glue on the dolly is properly applied prior to use
- C. Determine the Dry Film Thickness of the coating prior to use
- D. Consult SSPC Guide 1 prior to use
正解：A
質問 # 44
You should bulk store coatings containing isocyanates
- A. in a refrigerated warehouses.
- B. wherever it is convenient.
- C. in a well ventilated area separate from the work place.
- D. in a heated warehouse.
正解：C
質問 # 45
Ideally, documentation requirements should be defined:
- A. By the contractor
- B. By the inspector
- C. In the specification
- D. At the pre-job conference
正解：C
質問 # 46
Which concrete smoothing technique Involves scrubbing a mixture of cement mortal over the concrete surface using a cement sack, gunny sack, or sponge rubber float?
- A. High-pressure water washing
- B. Sacking
- C. Acid etching
- D. Stoning
正解：B
質問 # 47
When environmental enclosures ate being used an inspector needs to be concerned about:
- A. Lighting
- B. Structural integrity
- C. a), b), and c)
- D. Air changes
正解：C
質問 # 48
Coating application to concrete substrates is:
- A. Not required as concrete is Inorganic
- B. More challenging than coating steel
- C. The same as coating steel
- D. Less challenging than coating steel
正解：B
質問 # 49
Centrifugal blast cleaning requires:
- A. The use of single use abrasives
- B. A large volume of alt to propel the abrasive
- C. Well maintained blast wheels
- D. Very large nozzles
正解：C
質問 # 50
Corrosion Is the reverse process of
- A. flaking.
- B. galvanic deteroration.
- C. steel manufacturing.
- D. hot dipping.
正解：C
質問 # 51
Application of Thermal Spray Coatings requires:
- A. Specialized skills supported by training and experience
- B. The same skills as liquid coatings
- C. The same skills as welding
- D. No particular skills
正解：A
質問 # 52
External coatings applied to burled pipelines are generally tested for:
- A. Gloss level
- B. Solvent resistance
- C. Chalking resistance
- D. Cathodic disbondment
正解：D
質問 # 53
Which surface preparation method uses a dilute add solution to remove laitance and roughen the concrete surface?
- A. Add etching
- B. Sacking
- C. High-pressure water washing
- D. Stoning
正解：A
質問 # 54
......
あなたを合格させるAMPP試験でSenior-Internal-Corrosion-Technologist試験問題集：https://www.goshiken.com/AMPP/Senior-Internal-Corrosion-Technologist-mondaishu.html
Senior-Internal-Corrosion-Technologist試験問題集PDF更新された問題集：https://drive.google.com/open?id=1o7C1KmZvufQjJXMQHhpwheCkRpD1ZeKV