[2023年06月23日] 最速合格には素晴らしい200-301無料テストPDF本日更新です
無料でゲット！最新の2023年最新の有効な練習CCNA 200-301問題と解答でテストエンジン
Cisco 200-301認定試験は、シスコシステムズが提供する世界的に認知された認定試験です。この試験は、ネットワークの基礎、ネットワークアクセス、IP接続性、IPサービス、セキュリティの基礎、および自動化とプログラマビリティに関する個人の知識とスキルを検証するために設計されています。認定試験は、ネットワークのキャリアを開始する個人、または既にこの分野で働いていて知識とスキルを拡大したい個人を対象としています。
Cisco 200-301試験は、120の問題から構成され、時間制限は120分です。問題は、多肢選択、ドラッグアンドドロップ、シミュレーションなどがあります。試験はオンラインで実施され、世界中のPearson VUEテストセンターで受験できます。この認定はネットワーク業界で高く評価され、多くのジョブロールに必要な前提条件です。Cisco 200-301試験に合格することは、あなたの知識やスキルを検証するだけでなく、業界の他のネットワーク専門家から差をつけることができます。
質問 # 138
Refer to the exhibit.
A network engineer must configure R1 so that it sends all packets destined to the 10.0.0.0/24 network to R3, and all packets destined to PCI to R2. Which configuration must the engineer implement?
- A.
- B.
- C.
- D.
正解：C
質問 # 139
Refer to the Exhibit.
After the switch configuration the ping test fails between PC A and PC B Based on the output for switch 1. which error must be corrected?
- A. All VLANs are not enabled on the trunk
- B. There is a native VLAN mismatch
- C. Access mode is configured on the switch ports.
- D. The PCs are m the incorrect VLAN
正解：B
質問 # 140
What are two reasons that duplex mismatches can be difficult to diagnose? (Choose two.)
- A. Autonegotiation is disabled.
- B. Full-duplex interfaces use CSMA/CD logic, so mismatches may be disguised by collisions.
- C. 1-Gbps interfaces are full-duplex by default.
- D. The symptoms of a duplex mismatch may be intermittent.
- E. The interface displays a connected (up/up) state even when the duplex settings are mismatched.
正解：D、E
質問 # 141
Which QoS Profile is selected in the GUI when configuring a voice over WLAN deployment?
- A. Platinum
- B. Silver
- C. Bronze
- D. Gold
正解：A
解説：
Section: Network Access
Explanation:
Cisco Unified Wireless Network solution WLANs support four levels of QoS: Platinum/Voice, Gold/Video, Silver/Best Effort (default), and Bronze/Background.
Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-4/configuration/guides/consolidated/ b_cg74_CONSOLIDATED/b_cg74_CONSOLIDATED_chapter_01010111.html
質問 # 142
Drag and drop the network protocols from the left onto the correct transport services on the right.
正解：
解説：
質問 # 143
What is the purpose of a southbound API in a control based networking architecture?
- A. Facilities communication between the controller and the networking hardware
- B. integrates a controller with other automation and orchestration tools.
- C. allows application developers to interact with the network
- D. Facilities communication between the controller and the applications
正解：A
解説：
https://www.ciscopress.com/articles/article.asp?p=2995354&seqNum=2#:~:text=The%20Southbound%20Interface,communicate%20to%20the%20networking%20devices.&text=The%20overall%20goal%20is%20network,from%20being%20only%20a%20protocol.
The Southbound Interface
In a controller-based network architecture, the controller needs to communicate to the networking devices.
質問 # 144
Which command is used to verify the DHCP relay agent address that has been set up on your Cisco IOS router?
- A. show ip interface brief
- B. show interface
- C. show ip dhcp bindings
- D. show ip dhcp pool
- E. show ip interface
- F. show ip route
正解：E
解説：
Section: IP Services
質問 # 145
Refer to the exhibit. Which command would you use to configure a static route on Router1 to network 192.168.202.0/24 with a nondefault administrative distance?
- A. router1(config)#ip route 192.168.202.0 255.255.255.0 192.168.201.2 5
- B. router1(config)#ip route 192.168.202.0 255.255.255.0 192.168.201.2 1
- C. router1(config)#ip route 1 192.168.201.1 255.255.255.0 192.168.201.2
- D. router1(config)#ip route 5 192.168.202.0 255.255.255.0 192.168.201.2
正解：A
解説：
The default AD of static route is 1 so we need to configure another number for the static route.
質問 # 146
Which IOS troubleshooting tool should you use to direct system messages to your screen?
- A. terminal monitor
- B. local SPAN
- C. APIC-EM
- D. log events
正解：A
質問 # 147
Refer to the exhibit.
Which command configures a floating static route to provide a backup to the primary link?
- A. ip route 0.0.0.0 0.0.0.0 209.165.200.224
- B. ip route 209.165.200.224 255.255.255.224 209.165.202.129 254
- C. ip route 209.165.201.0 255.255.255.224 209.165.202.130
- D. ip route 0.0.0.0 0.0.0.0 209.165.202.131
正解：B
質問 # 148
Refer to the exhibit.
An extended ACL has been configured and applied to router R2 The configuration failed to work as intended Which two changes stop outbound traffic on TCP ports 25 and 80 to 10.0.20 0 26 from the 10.0.10 0/26 subnet while still allowing all other traffic? (Choose two )
- A. The ACL must be configured the Gi0/2 interface inbound on R1
- B. Add a "permit ip any any" statement to the begining of ACL 101 for allowed traffic.
- C. Add a "permit ip any any" statement at the end of ACL 101 for allowed traffic
- D. The source and destination IPs must be swapped in ACL 101
- E. The ACL must be moved to the Gi0/1 interface outbound on R2
正解：C、D
質問 # 149
which command should you enter to configure a DHCP client?
- A. ip helper-address
- B. ip dhcp client
- C. ip dhcp pool
- D. ip address dhcp
正解：D
質問 # 150
Which type of address is the public IP address of a NAT device?
- A. outside public
- B. inside global
- C. outside global
- D. inside local
- E. outside local
- F. inside public
正解：B
解説：
NAT use four types of addresses:
* Inside local address - The IP address assigned to a host on the inside network. The address is usually not an IP address assigned by the Internet Network Information Center (InterNIC) or service provider. This address is likely to be an RFC 1918 private address.
* Inside global address - A legitimate IP address assigned by the InterNIC or service provider that represents one or more inside local IP addresses to the outside world.
* Outside local address - The IP address of an outside host as it is known to the hosts on the inside network.
* Outside global address - The IP address assigned to a host on the outside network. The owner of the host assigns this address.
質問 # 151
Refer to the exhibit.
If configuring a static default route on the router with the ip route 0.0.0.0 0.0.0.0 10.13.0.1 120 command how does the router respond?
- A. It starts sending traffic without a specific matching entry in the routing table to GigabitEthernetO/1
- B. It ignores the new static route until the existing OSPF default route is removed
- C. It starts load-balancing traffic between the two default routes
- D. It immediately replaces the existing OSPF route in the routing table with the newly configured static route
正解：B
解説：
Explanation
Our new static default route has the Administrative Distance (AD) of 120, which is bigger than the AD of OSPF External route (O*E2) so it will not be pushed into the routing table until the current OSPF External route is removed.For your information, if you don't type the AD of 120 (using the command "ip route 0.0.0.0
0.0.0.0 10.13.0.1") then the new static default route would replace the OSPF default route as the default AD of static route is 1. You will see such line in the routing table:S* 0.0.0.0/0 [1/0] via 10.13.0.1
質問 # 152
Refer to the exhibit. Which command provides this output?
- A. show interface
- B. show ip interface
- C. show cdp neighbor
- D. show ip route
正解：C
質問 # 153
What is the default Syslog facility level?
- A. local 5
- B. local 6
- C. local 4
- D. local 7
正解：D
質問 # 154
Drag the descriptions of IP protocol transmissions from the left onto the IP traffic types on the right.
正解：
解説：
Explanation:
TCP
* Sends tranmissions in sequence
4. Transmits packets individually
6. Uses a lower transmission rate to ensure relability
UDP
5. Uses a higher transmission rate to support latency-sensitive application
2. Transmissions include an 8-byte header
3. Transmits packets as a stream
質問 # 155
A network administrator enabled port security on a switch interface connected to a printer. What is the next configuration action in order to allow the port to learn the MAC address of the printer and insert it into the table automatically?
- A. implement auto MAC address learning
- B. implement static MAC addressing
- C. enable sticky MAC addressing
- D. enable dynamic MAC address learning
正解：C
解説：
Section: Security Fundamentals
質問 # 156
Which two capacities of Cisco DNA Center make it more extensible? (Choose two)
- A. modular design that is upgradable as needed
- B. SDKs that support interaction with third-party network equipment
- C. adapters that support all families of Cisco IOS software
- D. REST APIs that allow for external applications to interact natively with Cisco DNA Center
- E. customized versions for small, medium, and large enterprises
正解：B、D
質問 # 157
Refer to the exhibit.
An extended ACL has been configured and applied to router R2 The configuration failed to work as intended Which two changes stop outbound traffic on TCP ports 25 and 80 to 10.0.20 0 26 from the 10.0.10 0/26 subnet while still allowing all other traffic? (Choose two )
- A. The ACL must be configured the Gi0/2 interface inbound on R1
- B. Add a "permit ip any any" statement to the begining of ACL 101 for allowed traffic.
- C. Add a "permit ip any any" statement at the end of ACL 101 for allowed traffic
- D. The source and destination IPs must be swapped in ACL 101
- E. The ACL must be moved to the Gi0/1 interface outbound on R2
正解：C、D
質問 # 158
Refer to the exhibit.
Users on existing VLAN 100 can reach sites on the Internet. Which action must the administrator take to establish connectivity to the Internet for users in VLAN 200?
- A. Define a NAT pool on the router.
- B. Configure static NAT translations for VLAN 200.
- C. Configure the ip nat outside command on another interface for VLAN 200.
- D. Update the NAT INSIDF RANGFS ACL
正解：B
質問 # 159
What is a reason to configure a trunk port that connects to a WLC distribution port?
- A. Permit multiple VLANs to provide out-of-band management.
- B. Allow multiple VLAN to be used in the data path.
- C. Eliminate redundancy with a link failure in the data path.
- D. Provide redundancy if there is a link failure for out-of-band management.
正解：A
質問 # 160
What are two functions of a Layer 2 switch? (Choose two.)
- A. moves packets between different VLANs
- B. selects the best route between networks on a WAN
- C. makes forwarding decisions based on the MAC address of a packet
- D. moves packets within a VLAN
- E. acts as a central point for association and authentication servers
正解：C、D
解説：
Section: Network Fundamentals
質問 # 161
Refer to Exhibit. How does SW2 interact with other switches in this VTP domain?
- A. It receives updates from all VTP servers and forwards all locally configured VLANs out all trunk ports
- B. It processes VTP updates from any VTP clients on the network on its access ports.
- C. It transmits and processes VTP updates from any VTP Clients on the network on its trunk ports
- D. It forwards only the VTP advertisements that it receives on its trunk ports.
正解：D
解説：
The VTP mode of SW2 is transparent so it only forwards the VTP updates it receives to its trunk links without processing them.
質問 # 162
When you deploy multilink PPP on your network, where must you configure the group IP Address on each device?
- A. in the global config
- B. Under serial interface
- C. Under the multilink interface
- D. Under the routing protocol
正解：C
質問 # 163
......
CCNA認定を取得することは、Ciscoテクノロジーやソリューションを扱う能力を証明し、どの組織にとっても貴重な資産となります。CCNA認定を取得したプロフェッショナルは、ネットワークエンジニア、ネットワーク管理者、サポートエンジニアなど、さまざまな役割で働くことができます。この認定は、Cisco Certified Network Professional（CCNP）やCisco Certified Internetwork Expert（CCIE）など、より高度なCisco認定のステップストーンとしても機能します。
200-301問題集PDFで100%合格保証付き：https://www.goshiken.com/Cisco/200-301-mondaishu.html
最新200-301のPDF問題集リアル無料テスト本日更新です：https://drive.google.com/open?id=1DYeyRcRVijLq3LOGjJE9uFsWTgrU3p87