信頼できるCIP Level 1 NACE-CIP1-001問題集PDF2022年03月16日最近更新された問題
必ず合格できるNACE NACE-CIP1-001試験正確な100問題と解答あります
質問 27
Good records can provide maintenance departments with detailed information about ALL of the following EXCEPT
- A. what materials were used.
- B. how the item was coated.
- C. what items were coated.
- D. when the coating will be reapplied.
正解: B
質問 28
If a Thermoset coating is heated it will:
- A. Harden and return to its original hardness when cooled
- B. Harden and retain its hardness when cooled
- C. Soften when heated and retain its softness when cooled
- D. Soften when heated and return to its original hardness when cooled
正解: B
質問 29
Non Conformance Reports are completed by the Inspector:
- A. In accordance with the specification's definition of a non-conformance
- B. When the Inspector and Contractor deem it to be a significant non-conforming item
- C. When the Inspector deems it to be a significant non-conforming item
- D. In every instance that an item does not meet the specification requirements
正解: B
質問 30
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Ultra-Violet light may contaminant the surface
- B. Presence of weld spatter may produce a false positive
- C. Synthetic oil or grease may not be identified
- D. Chloride salt may produce a false positive
正解: C
質問 31
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. alligatoring.
- B. blistering.
- C. cracking.
- D. checking.
正解: D
質問 32
The most important factor resulting in improved job site safety is:
- A. Situational Awareness
- B. Safety Enforcement
- C. Engineering Controls
- D. Personal Protective Equipment
正解: A
質問 33
Excess moisture during holiday testing can cause erroneous indications by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection.
This is often referred to as:
- A. telegraphing.
- B. juxtaposing.
- C. transitioning.
- D. monitoring
正解: A
質問 34
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Meet with the prospective employer to determine the scope of your role
- B. Advise the prospective employer that you cannot accept the position
- C. Review the NACE Attestation prior to making a decision
- D. Accept the assignment without hesitation
正解: A
質問 35
Galvanic corrosion occurs on which of the following substrates:
- A. Fiberglass Reinforced Plastic
- B. Wood
- C. Concrete
- D. Metal
正解: D
質問 36
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 75 Gauge Readings resulting in 25 Spot Measurements
- B. 45 Gauge readings resulting in 15 Spot Measurements
- C. 105 Gauge Readings resulting in 35 Spot Measurements
- D. 225 Gauge Readings resulting in 75 Spot Measurements
正解: D
質問 37
Digital hygrometers
- A. are used to measure temperature from a distance.
- B. use a thermocouple in contact with the surface to measure temperature
- C. consist of a bimetallic sensing element protected from wind gusts.
- D. determine relative humidity, air temperature, and dew point temperature:
正解: D
質問 38
The main responsibilities of the inspector are to
- A. demonstrate to the contractor how to apply the coating.
- B. direct and perform the work stated in the specification.
- C. observe and direct the work of the contractors.
- D. observe and report the quality of the work performed.
正解: D
質問 39
The initial steel condition is important to the NACE Inspector because:
- A. The Inspector may have to reject the Steel
- B. Less abrasive is need if the mill Scale s gone
- C. It affects the final appearance after blasting
- D. If the steel is pitted more coating will be required
正解: A
質問 40
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
- A. Call the coating manufacturer for clarification
- B. Use the job specification as a guide
- C. Call the person who wrote the specification for clarification
- D. Use the product data sheet as a guide
正解: B
質問 41
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Shut the job down
- C. Review the relevant standard with the Contractor
- D. Permit coating to take place so as not to lose the blast
正解: C
質問 42
Prior to using Inspection Tools the inspector must:
- A. Read the manufactures' instructions
- B. Be trained on how to use the instrument
- C. Ensure the instrument is within calibration parameters
- D. a), b) & c)
正解: D
質問 43
......
2022年最新の実際にある検証済みのNACE-CIP1-001問題集：https://www.goshiken.com/NACE/NACE-CIP1-001-mondaishu.html
合格させるNACE-CIP1-001試験で更新された100問題あります：https://drive.google.com/open?id=16G1QgNblilKpDVEDuYnuimCIa3C6SjEY