[2023年更新]NACE-CIP1-001はCIP Level 1リアルな無料試験練習テスト
無料CIP Level 1 NACE-CIP1-001試験問題を提供します
NACE-CIP1-001コーティング検査士レベル1試験は、世界的に認められ、コーティング検査業界で高い評価を得ています。この認証プログラムは、基本的なコーティング検査を実行するために必要なスキルと知識を個人に提供するよう設計されています。このプログラムは、コーティング検査業界でスキルと知識を向上させ、認定されたコーティング検査士になりたいと考えている個人に最適です。
質問 # 56
According to SSPC PA 2 a Spot Measurement is:
- A. A single gauge reading
- B. The average of all spot measurements in a given area
- C. The average of gauge readings taken in a 4cm (1.5 inch) circle
- D. The overall average of all readings
正解：C
質問 # 57
The main responsibilities of the inspector are to
- A. demonstrate to the contractor how to apply the coating.
- B. observe and report the quality of the work performed.
- C. direct and perform the work stated in the specification.
- D. observe and direct the work of the contractors.
正解：B
質問 # 58
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use
- A. their best judgment based on similar projects and specifications.
- B. a detailed checklist and document the lack of a standard.
- C. a recognized industry standard like SSPC-PA 2 that is broadly accepted
- D. NACE 2/SSPC SP10
正解：C
質問 # 59
When applying Thermal Spray Coatings the specification is most likely to refence:
- A. NACE SP 0188
- B. SSPC PA 2
- C. SSPC-CS 23.00/AWS C2.23/NACE No. 12
- D. NACE SP 0178
正解：C
質問 # 60
Removal of surface contaminants is done by:
- A. Waterjetting
- B. Scarifying
- C. A combination of methods
- D. Abrasive blasting
正解：C
質問 # 61
Stripe coats are generally applied to:
- A. a), b), and c)
- B. Edges and corners
- C. Welds
- D. Complex geometric shapes
正解：A
質問 # 62
Which one of these elements is not necessary for corrosion to occur:
- A. Electrolyte
- B. Cathode
- C. Anode
- D. Reference Cell
正解：D
質問 # 63
Silicone coatings are typically:
- A. Used strictly in immersion service
- B. Applied in very thick films
- C. Applied in very' thin films
- D. Used as a sacrificial primer
正解：C
質問 # 64
Safety Data Sheets must be carefully reviewed by:
- A. The Owner's personnel
- B. All personnel involved in the job
- C. The Inspection personnel
- D. The Application personnel
正解：B
質問 # 65
ISO SA 2.5 is defined as:
- A. Very Thorough Blast Cleaning
- B. Light Blast Cleaning
- C. Thorough Blast Cleaning
- D. Near White Metal Blasting
正解：A
質問 # 66
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Surface Condition H
- B. Rust Grades 1-4
- C. Rust Grades A-D
- D. Surface Conditions E-G
正解：C
質問 # 67
Digital hygrometers
- A. consist of a bimetallic sensing element protected from wind gusts.
- B. are used to measure temperature from a distance.
- C. determine relative humidity, air temperature, and dew point temperature:
- D. use a thermocouple in contact with the surface to measure temperature
正解：C
質問 # 68
Check abrasive blast pressure close to the
- A. compressor
- B. blast nozzle
- C. blast pot
- D. substrate
正解：B
質問 # 69
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?
- A. 6 to 7 mils (150 to 175 microns)
- B. 5 to 6 mils (125 to 150 microns)
- C. 10 to 12 mils (250 to 300 microns)
- D. 8 to 10 mils (200 to 250 microns)
正解：A
質問 # 70
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. A method to grade surface profile
- B. A final conflict resolution method
- C. A general guide
- D. Pass/fail criteria
正解：C
質問 # 71
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Keep doing the checks regardless
- B. Skip the checks and just record the same readings as you have been getting
- C. Keep doing the checks and consult the Owner's representative for direction
- D. Skip the checks as you are. confident the blast pressure is OK
正解：C
質問 # 72
Prior to using Inspection Tools the inspector must:
- A. Be trained on how to use the instrument
- B. Ensure the instrument is within calibration parameters
- C. a), b) & c)
- D. Read the manufactures' instructions
正解：C
質問 # 73
If a Thermoset coating is heated it will:
- A. Soften when heated and retain its softness when cooled
- B. Harden and return to its original hardness when cooled
- C. Harden and retain its hardness when cooled
- D. Soften when heated and return to its original hardness when cooled
正解：C
質問 # 74
Most industrial coatings are:
- A. Resistant to temperatures above 200C
- B. Resistant to concentrated sulfuric acid
- C. Organic
- D. Inorganic
正解：C
質問 # 75
The most important factor resulting in improved job site safety is:
- A. Situational Awareness
- B. Safety Enforcement
- C. Engineering Controls
- D. Personal Protective Equipment
正解：A
質問 # 76
Stripe coats are best applied by:
- A. Airless spray
- B. High volume low pressure spray
- C. Brush
- D. Conventional spray
正解：C
質問 # 77
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Check the PPE used by the Applicators
- B. Check the credentials of the Safety Officer on site
- C. Assume the role of the Safety Inspector
- D. Act in accordance with the site safety requirements and set an example
正解：D
質問 # 78
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. False
- B. True
正解：B
質問 # 79
Removal of welds splatter is required:
- A. On every job
- B. When ISO abrasive blast standards are specified
- C. When specifically identified in the owner's specification
- D. When NACE/SSPC abrasive blast standards are specified
正解：C
質問 # 80
......
NACE NACE-CIP1-001リアルな問題と知能問題集：https://www.goshiken.com/NACE/NACE-CIP1-001-mondaishu.html
NACE-CIP1-001問題集でCIP Level 1高確率練習問題集：https://drive.google.com/open?id=16G1QgNblilKpDVEDuYnuimCIa3C6SjEY