[2024年04月14日]NACE-CIP1-001試験問題集で100%合格率NACE-CIP1-001試験！
試験問題集リアルCIP Level 1問題集100解答を試そう！
NACE-CIP1-001試験は、100の質問で構成される3時間半の複数選択テストです。この試験では、基本的な腐食原理、表面の準備、コーティングアプリケーション方法、コーティングタイプ、検査技術などのトピックについて説明します。候補者は、認定を受け取るために、最低スコア70％で試験に合格する必要があります。 CIPレベル1認定は5年間有効であり、特定の継続教育要件を完了することで更新できます。この認定は、個人に雇用市場で競争上の優位性を提供し、コーティング業界で高い基準を維持するというコミットメントを実証しています。
NACE-CIP1-001認定は、業界で非常に尊敬されており、世界中の雇用主によって認められています。この認定は、コーティング検査と腐食制御に関する個人の専門知識を示しており、あらゆる組織にとって貴重な資産となっています。腐食制御の専門家の需要が増加し続けるにつれて、NACE-CIP1-001認定を取得すると、新しいキャリアの機会とより高い収益の可能性につながる可能性があります。
質問 # 51
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Permit coating to take place so as not to lose the blast
- C. Review the relevant standard with the Contractor
- D. Shut the job down
正解：C
質問 # 52
Corrosion generally occurs at which of the following sites:
- A. Metallic pathway
- B. Cathode
- C. Anode
- D. Electrolyte
正解：C
質問 # 53
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a
- A. vial lest.
- B. wet film thickness (WFT) measurement.
- C. dry film thickness (DEI) measurement.
- D. blotter test for the presence of oil and water.
正解：D
質問 # 54
It is good practice for the NACE Inspector to have instrument calibration certificates available:
- A. At all times
- B. Only if the specification requires it
- C. In the office only
- D. In the field only
正解：A
質問 # 55
Removal of welds splatter is required:
- A. On every job
- B. When NACE/SSPC abrasive blast standards are specified
- C. When specifically identified in the owner's specification
- D. When ISO abrasive blast standards are specified
正解：C
質問 # 56
Passivation can best be described as:
- A. Treating metal with a liquid inhibiter
- B. Complete elimination pf the corrosion process
- C. A protective metallic oxide surface layer that slows corrosion
- D. A coating layer applied to the surface to inhibit corrosion
正解：C
質問 # 57
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Check the PPE used by the Applicators
- B. Assume the role of the Safety Inspector
- C. Act in accordance with the site safety requirements and set an example
- D. Check the credentials of the Safety Officer on site
正解：C
質問 # 58
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. It depends on which hand tool the Contractor selects
- B. No, because there is no real difference in the standards
- C. Yes, because the 'two standards are not equivalent
- D. It depends on which power tool the Contractor selects
正解：B
質問 # 59
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Extract any liquid that may be inside the blister and send it to the lab for further analysis
- B. Break the blisters to see what's inside
- C. Document the problem and advise the Contractor and Owner's representative
- D. Document the problem and advise the Contractor
正解：C
質問 # 60
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. A method to grade surface profile
- B. A final conflict resolution method
- C. A general guide
- D. Pass/fail criteria
正解：C
質問 # 61
Owners hire NACE Inspectors' with the expectation that:
- A. The Inspector will make a meaningful technical contribution to the job
- B. The inspection cost will be offset by an improvement in service life
- C. a) and c)
- D. The Inspector will improve job flow and schedule
正解：C
質問 # 62
An inspectors personal log book should contain:
- A. The inspector's personal opinions of the application team
- B. No comments regarding the application team
- C. Subjective comments re ding the application team
- D. Objective comments regarding the application work
正解：B
質問 # 63
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Record the segment with the less aggressive profile
- B. Record the segment with the more aggressive profile
- C. Use another method as the comparator method is too subjective
- D. Record your result by identifying two segments
正解：A
質問 # 64
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 2.5 cm (1 inch)
- B. 1 cm (.39 inch)
- C. 6.35 cm (2.5 inch)
- D. 2.5 millimeters (.10 inch)
正解：A
質問 # 65
The least effective method of surface cleaning is most likely
- A. dry grit blasting.
- B. power tool cleaning.
- C. hand tool cleaning.
- D. water blasting.
正解：C
質問 # 66
......
NACE-CIP1-001試験は、コーティング検査官として認定を求めている個人の知識とスキルをテストするように設計されています。この試験では、表面の準備、コーティングの適用、検査技術、安全性など、さまざまなトピックをカバーしています。試験は75の複数選択の質問で構成されており、2時間の時間制限があります。
あなたを余裕でNACE-CIP1-001試験合格させます！100%高合格率保証：https://www.goshiken.com/NACE/NACE-CIP1-001-mondaishu.html
NACE-CIP1-001問題集本日限定！無料アクセス可能に！：https://drive.google.com/open?id=16G1QgNblilKpDVEDuYnuimCIa3C6SjEY