[2024年02月] 試験NACE-CIP1-001最新ブレーン専門問題集はここ
無料で使えるNACE-CIP1-001試験問題集試験点数を伸ばそう
NACE-CIP1-001（コーティングインスペクターレベル1）認定試験は、コーティング業界または関連分野で働く個人にとって貴重なプログラムです。この認定は、認定コーティング検査官になるために必要な知識とスキルを個人に提供し、キャリアの進歩と雇用機会の増加につながる可能性があります。厳密なテスト要件と実際のアプリケーションに焦点を当てているNACE-CIP1-001認証は、業界で非常に尊敬されており、コーティング検査でのキャリアを促進したい人にとって貴重な資産です。
質問 # 24
A NACE Coating Inspector is permitted to transport coating material when:
- A. Asked to do so by the Coating Application team
- B. If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods
- C. Asked to do so by the Owner's Representative
- D. The Inspector should never transport coating material
正解：D
質問 # 25
A magnetic pull-off type gauge is a good choice when:
- A. When working on non-ferrous metals
- B. When an intrinsically safe tool is required
- C. Accuracy is not required
- D. Performing an adhesion test
正解：B
質問 # 26
Removal of welds splatter is required:
- A. When specifically identified in the owner's specification
- B. When ISO abrasive blast standards are specified
- C. When NACE/SSPC abrasive blast standards are specified
- D. On every job
正解：A
質問 # 27
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. False
- B. True
正解：B
質問 # 28
To be of value the Inspector's documentation must be:
- A. Timely, accurate and concise
- B. Submitted before the end of the job
- C. Always handwritten
- D. Always typewritten
正解：A
質問 # 29
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Act in accordance with the site safety requirements and set an example
- B. Check the PPE used by the Applicators
- C. Assume the role of the Safety Inspector
- D. Check the credentials of the Safety Officer on site
正解：A
質問 # 30
Which one of these elements is not necessary for corrosion to occur:
- A. Cathode
- B. Anode
- C. Electrolyte
- D. Reference Cell
正解：D
質問 # 31
Check abrasive blast pressure close to the
- A. compressor
- B. blast pot
- C. substrate
- D. blast nozzle
正解：D
質問 # 32
An inspectors personal log book should contain:
- A. Objective comments regarding the application work
- B. The inspector's personal opinions of the application team
- C. Subjective comments re ding the application team
- D. No comments regarding the application team
正解：D
質問 # 33
ASTM Standards are applicable:
- A. In North America
- B. In the USA
- C. In Asia
- D. When specified
正解：D
質問 # 34
NACE SP 0178 is a standard for:
- A. Tanks and Vessels to, be Lined for Immersion Service
- B. Stainless steel pipe to be Externally Coated
- C. Structural steel to be coated for Atmospheric Service
- D. Tanks and Vessels to be Externally Coated
正解：A
質問 # 35
Check abrasive blast pressure with a
- A. nozzle aperature gauge
- B. needle pressure gauge
- C. replica tape
- D. surface comparator
正解：B
質問 # 36
The NACE Inspector should perform tests for soluble salts:
- A. After surface preparation
- B. Prior to coating application
- C. Prior to surface preparation
- D. When specified
正解：D
質問 # 37
The most important factor resulting in improved job site safety is:
- A. Situational Awareness
- B. Safety Enforcement
- C. Engineering Controls
- D. Personal Protective Equipment
正解：A
質問 # 38
Which one of the following documents is the best source for coating technical data:
- A. Application Guidelines
- B. Specification
- C. Technical Data Sheet
- D. Safety Data Sheet;
正解：C
質問 # 39
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Extract any liquid that may be inside the blister and send it to the lab for further analysis
- B. Break the blisters to see what's inside
- C. Document the problem and advise the Contractor and Owner's representative
- D. Document the problem and advise the Contractor
正解：C
質問 # 40
Whenever dissimilar metals must join, the most common practice is to
- A. provide anodic protection to prevent corrosion.
- B. avoid coating all connected dissimilar metals.
- C. coat all connected dissimilar metals.
- D. provide cathodic protection to prevent corrosion,
正解：C
質問 # 41
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Record the segment with the more aggressive profile
- B. Use another method as the comparator method is too subjective
- C. Record the segment with the less aggressive profile
- D. Record your result by identifying two segments
正解：C
質問 # 42
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Default to the owner's Inspection and Test Plan
- B. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
- C. Bring the matter up at the pre-job conference
- D. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
正解：C
質問 # 43
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Dragging a gauge through wet coating
- B. Using a damaged gauge
- C. Placing the gauge along the longitudinal axis
正解：A、B
質問 # 44
In a non-convertible coating the role of the primary solvent is to:
- A. To control the evaporation rate
- B. To make the coating flow out better
- C. To promote faster cure
- D. To dissolve the resin
正解：A
質問 # 45
Solvents are added to coating formulations to
- A. decrease film permeability.
- B. dissolve binders and form liquid coatings.
- C. provide color.
- D. increase film permeability.
正解：B
質問 # 46
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. A final conflict resolution method
- B. Pass/fail criteria
- C. A method to grade surface profile
- D. A general guide
正解：D
質問 # 47
......
NACE-CIP1-001試験は、コーティングインスペクターレベル1として認定されたい個人の知識とスキルをテストするように設計されています。 NACEは、腐食制御と予防の基準を設定する世界的に認められた組織です。認定は、コーティングと腐食の分野での個人の専門知識を示す業界に認識された資格情報です。
心強いNACE-CIP1-001のPDF問題集はNACE-CIP1-001問題：https://www.goshiken.com/NACE/NACE-CIP1-001-mondaishu.html
2024年最新の実際に出るNACE-CIP1-001問題集には試験のコツがあるPDF試験材料：https://drive.google.com/open?id=16G1QgNblilKpDVEDuYnuimCIa3C6SjEY