2025年最新の実際に出るNACE-CIP1-001問題集には試験のコツがあるPDF試験材料
心強いNACE-CIP1-001PDF問題集はNACE-CIP1-001問題
NACE-CIP1-001試験は、塗装検査業界で働く個人にとって必要不可欠な認定試験です。この試験に合格することは、塗装検査における高度な能力、知識、スキルを示し、世界的に認知されます。この試験は、多岐にわたるトピックをカバーし、合格基準は70％です。認定は5年間有効であり、個人は認定ステータスを維持するために再認定する必要があります。
質問 # 45
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 45 Gauge readings resulting in 15 Spot Measurements
- B. 105 Gauge Readings resulting in 35 Spot Measurements
- C. 225 Gauge Readings resulting in 75 Spot Measurements
- D. 75 Gauge Readings resulting in 25 Spot Measurements
正解：C
質問 # 46
Dew point is the temperature at which
- A. condensation occurs.
- B. the air is saturated.
- C. humidity decreases
- D. water freezes.
正解：A
質問 # 47
The Inspector's Log Book is generally:
- A. Shredded by the inspector upon project completion
- B. Shared with all parties upon project completion
- C. Submitted to the client upon project completion
- D. Retained by the inspector upon project completion
正解：D
質問 # 48
Owners hire NACE Inspectors' with the expectation that:
- A. The inspection cost will be offset by an improvement in service life
- B. The Inspector will improve job flow and schedule
- C. a) and c)
- D. The Inspector will make a meaningful technical contribution to the job
正解：C
質問 # 49
Safety Data Sheets must be carefully reviewed by:
- A. The Application personnel
- B. The Owner's personnel
- C. All personnel involved in the job
- D. The Inspection personnel
正解：C
質問 # 50
Check abrasive blast pressure with a
- A. needle pressure gauge
- B. nozzle aperature gauge
- C. replica tape
- D. surface comparator
正解：A
質問 # 51
Conventional spray is a good choice when:
- A. High production rates are required
- B. High quality finishes are required
- C. High viscosity coatings are being applied
- D. High transfer efficiency is required
正解：B
質問 # 52
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
正解：A
質問 # 53
An Inspector should change position when:
- A. The Inspector is convinced by verifiable facts
- B. Only when directed by the supervisor
- C. The Inspectors position is not the majority position
- D. The Owner can save some money by the change
正解：A
質問 # 54
Digital hygrometers
- A. use a thermocouple in contact with the surface to measure temperature
- B. determine relative humidity, air temperature, and dew point temperature:
- C. are used to measure temperature from a distance.
- D. consist of a bimetallic sensing element protected from wind gusts.
正解：B
質問 # 55
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 1
- B. Level 2
- C. Level 4
- D. Level 3
正解：D
質問 # 56
Good records can provide maintenance departments with detailed information about ALL of the following EXCEPT
- A. how the item was coated.
- B. what materials were used.
- C. when the coating will be reapplied.
- D. what items were coated.
正解：A
質問 # 57
Removal of surface contaminants is done by:
- A. Scarifying
- B. Waterjetting
- C. Abrasive blasting
- D. A combination of methods
正解：D
質問 # 58
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing
- A. develops a good anchor profile resulting in uneven coating application.
- B. develops a polished surface, which is a poor anchor profile for most coatings
- C. scratches the surface too deeply resulting in uneven coating application
- D. damages structural elements thereby speeding up the corrosion process.
正解：B
質問 # 59
Checking is
- A. an exposed area of the substrate or previous coat material, caused by poor application technique.
- B. surface breaks in the film that often result from grease or oil contamination and revel the substrate.
- C. a fine crack in the surface of a coating that rarely reaches the substrate
- D. a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.
正解：C
質問 # 60
In a non-convertible coating the role of the primary solvent is to:
- A. To dissolve the resin
- B. To control the evaporation rate
- C. To promote faster cure
- D. To make the coating flow out better
正解：B
質問 # 61
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- B. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- C. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
- D. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
正解：C
質問 # 62
Due to a previous premature coating failure the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three coat system at the applicator's cost. Due to the financial implications of another failure, the owner has offered you the job as the NACE CIP Level 1 Coating Inspector and explained that he expects you to be his "insurance policy" for this job. You have never been involved in a warranty job before and are unfamiliar with the coating system.
Your preferred FIRST course of action is to:
- A. Purchase Professional Liability Insurance prior to job commencement
- B. Review the Product Data Sheets, and conduct a walk thru of the job site prior to the pre-job Conference
- C. Review the Product Data Sheets and meet with the Coating Applicator 'prior to the pre-job meeting
- D. Meet with the owner and explain your limitations and concerns prior accepting the assignment
正解：B
質問 # 63
If a Thermoset coating is heated it will:
- A. Soften when heated and return to its original hardness when cooled
- B. Harden and return to its original hardness when cooled
- C. Harden and retain its hardness when cooled
- D. Soften when heated and retain its softness when cooled
正解：C
質問 # 64
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 2.5 millimeters (.10 inch)
- B. 2.5 cm (1 inch)
- C. 6.35 cm (2.5 inch)
- D. 1 cm (.39 inch)
正解：B
質問 # 65
Which one of the following documents is the best source for coating technical data:
- A. Application Guidelines
- B. Specification
- C. Technical Data Sheet
- D. Safety Data Sheet;
正解：C
質問 # 66
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 80% of the specified minimum thickness
- B. 90% of the specified maximum thickness
- C. 70% of the specified maximum thickness
- D. 100% of the specified maximum thickness
正解：A
質問 # 67
Inspection documentation is important because:
- A. Owners use the documentation for a variety of purposes
- B. It is the only deliverable item provided by the inspector
- C. a) only
- D. a) & b)
正解：A
質問 # 68
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Never change his/her mind
- B. Call the supervisor
- C. Achieve consensus through negotiation
- D. Go with the majority opinion
正解：B
質問 # 69
......
結果を保証するには最新2025年04月無料：https://www.goshiken.com/NACE/NACE-CIP1-001-mondaishu.html
正真正銘のNACE-CIP1-001問題集で無料PDF問題で合格させる：https://drive.google.com/open?id=13Igy44GKJ8npZBcAbNG5wwtkKYBlwhC8