[2026年03月05日]NACE-CIP1-001テスト準備できるトレーニング練習テスト試験問題
試験問題解答ブレーン問題集でNACE-CIP1-001試験問題集PDFを使おう
NACE-CIP1-001試験に合格するには、候補者はNACE承認のトレーニングプログラムの修了または塗装業界での最低6か月間の経験を含む特定の要件を満たす必要があります。この試験は、世界中の腐食制御専門家のためのトレーニング、認証、および標準開発を提供する主要な組織であるNACE Internationalによって実施されます。
質問 # 58
If a Thermoset coating is heated it will:
- A. Soften when heated and retain its softness when cooled
- B. Harden and return to its original hardness when cooled
- C. Soften when heated and return to its original hardness when cooled
- D. Harden and retain its hardness when cooled
正解：D
質問 # 59
Galvanic corrosion occurs on which of the following substrates:
- A. Metal
- B. Concrete
- C. Wood
- D. Fiberglass Reinforced Plastic
正解：A
質問 # 60
Upon arrival of coating materials, the inspector should
- A. observe and document time frame and environmental conditions between each coat.
- B. observe aryl document that the applicator WFT at regular intervals during application.
- C. observe and document the amount of material and batch numbers.
- D. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
正解：C
質問 # 61
Whenever dissimilar metals must join, the most common practice is to
- A. coat all connected dissimilar metals.
- B. provide cathodic protection to prevent corrosion,
- C. provide anodic protection to prevent corrosion.
- D. avoid coating all connected dissimilar metals.
正解：A
質問 # 62
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Act in accordance with the site safety requirements and set an example
- B. Check the PPE used by the Applicators
- C. Check the credentials of the Safety Officer on site
- D. Assume the role of the Safety Inspector
正解：A
質問 # 63
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Chloride salt may produce a false positive
- B. Presence of weld spatter may produce a false positive
- C. Ultra-Violet light may contaminant the surface
- D. Synthetic oil or grease may not be identified
正解：D
質問 # 64
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Rust Grades A-D
- B. Surface Conditions E-G
- C. Surface Condition H
- D. Rust Grades 1-4
正解：A
質問 # 65
A magnetic pull-off type gauge is a good choice when:
- A. Accuracy is not required
- B. When an intrinsically safe tool is required
- C. Performing an adhesion test
- D. When working on non-ferrous metals
正解：B
質問 # 66
To be of value the Inspector's documentation must be:
- A. Always typewritten
- B. Submitted before the end of the job
- C. Timely, accurate and concise
- D. Always handwritten
正解：C
質問 # 67
Passivation can best be described as:
- A. A protective metallic oxide surface layer that slows corrosion
- B. Complete elimination pf the corrosion process
- C. Treating metal with a liquid inhibiter
- D. A coating layer applied to the surface to inhibit corrosion
正解：A
質問 # 68
ISO SA 3 is directly equivalent to:
- A. NACE No. 1/SSPC SP 5
- B. None of the above
- C. NACE No. 3/SSPC SP 6
- D. NACE No. 2/SSPC SP 10
正解：B
質問 # 69
Which one of the following documents is the best source for coating technical data:
- A. Specification
- B. Safety Data Sheet;
- C. Application Guidelines
- D. Technical Data Sheet
正解：D
質問 # 70
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 2.5 cm (1 inch)
- B. 1 cm (.39 inch)
- C. 2.5 millimeters (.10 inch)
- D. 6.35 cm (2.5 inch)
正解：A
質問 # 71
What is used to determine compressed air cleanliness?
- A. Blotter test
- B. Psychrometer
- C. Profilometer
- D. Needle pressure gauge
正解：C
質問 # 72
NACE Level 1 Inspectors have been trained to perform:
- A. All types of inspection
- B. Visual inspection and Non-destructive testing
- C. Visual inspection only
- D. Visual inspection, Non-Destructive and Destructive testing
正解：B
質問 # 73
According to SSPC PA 2 a Spot Measurement is:
- A. A single gauge reading
- B. The average of all spot measurements in a given area
- C. The overall average of all readings
- D. The average of gauge readings taken in a 4cm (1.5 inch) circle
正解：D
質問 # 74
ISO SA 2 is defined as:
- A. Thorough Blast Cleaning
- B. Near White Metal Blasting
- C. Very Thorough Blast Cleaning
- D. Light Blast Cleaning
正解：A
質問 # 75
Checking is
- A. an exposed area of the substrate or previous coat material, caused by poor application technique.
- B. a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.
- C. a fine crack in the surface of a coating that rarely reaches the substrate
- D. surface breaks in the film that often result from grease or oil contamination and revel the substrate.
正解：C
質問 # 76
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Call your supervisor
- B. Advise the Contractor of your readings
- C. Advise the Contractor he can proceed
- D. Advise the Contractor he cannot proceed
正解：B
質問 # 77
......
NACE-CIP1-001試験は、コーティング産業でキャリアを追求したい個人や、コーティング検査の分野での知識とスキルを向上させたい人々に最適です。認定資格は、コーティング検査員を雇用する企業にとっても有益であり、従業員が職務を効果的に遂行するために必要な専門知識を有していることを保証します。
無料ダウンロードNACE NACE-CIP1-001リアルな試験問題で合格しよう：https://www.goshiken.com/NACE/NACE-CIP1-001-mondaishu.html
NACE-CIP1-001試験問題集、NACE-CIP1-001練習テスト問題：https://drive.google.com/open?id=1912E0KIfySC3DoKpzzRRqhEvDM4-sAQV