NACE-CIP1-001ブレーン問題集リアル試験最新問題2024年12月20日には100問題
最新NACE-CIP1-001のPDF問題集リアル無料テスト本日更新です
NACE-CIP1-001試験は、塗装検査業界で働く個人にとって必要不可欠な認定試験です。この試験に合格することは、塗装検査における高度な能力、知識、スキルを示し、世界的に認知されます。この試験は、多岐にわたるトピックをカバーし、合格基準は70％です。認定は5年間有効であり、個人は認定ステータスを維持するために再認定する必要があります。
質問 # 17
Owners hire NACE Inspectors' with the expectation that:
- A. The Inspector will make a meaningful technical contribution to the job
- B. a) and c)
- C. The inspection cost will be offset by an improvement in service life
- D. The Inspector will improve job flow and schedule
正解：B
質問 # 18
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. soluble chemical salts
- B. grease and oil
- C. sulfates
- D. inhibitor residues
正解：B
質問 # 19
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor of your readings
- B. Advise the Contractor he cannot proceed
- C. Advise the Contractor he can proceed
- D. Call your supervisor
正解：A
質問 # 20
When applying Thermal Spray Coatings the specification is most likely to refence:
- A. NACE SP 0188
- B. SSPC PA 2
- C. SSPC-CS 23.00/AWS C2.23/NACE No. 12
- D. NACE SP 0178
正解：C
質問 # 21
The form of corrosion that has the largest potential for unexpected catastrophic failure is:
- A. Localized Corrosion
- B. Galvanic Corrosion
- C. Atmospheric Corrosion
- D. General Corrosion
正解：B
質問 # 22
An Inspector should change position when:
- A. The Inspector is convinced by verifiable facts
- B. The Inspectors position is not the majority position
- C. Only when directed by the supervisor
- D. The Owner can save some money by the change
正解：A
質問 # 23
A magnetic pull-off type gauge is a good choice when:
- A. Performing an adhesion test
- B. When an intrinsically safe tool is required
- C. Accuracy is not required
- D. When working on non-ferrous metals
正解：B
質問 # 24
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?
- A. 10 to 12 mils (250 to 300 microns)
- B. 6 to 7 mils (150 to 175 microns)
- C. 8 to 10 mils (200 to 250 microns)
- D. 5 to 6 mils (125 to 150 microns)
正解：B
質問 # 25
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. checking.
- B. cracking.
- C. blistering.
- D. alligatoring.
正解：A
質問 # 26
An inspectors personal log book should contain:
- A. Subjective comments re ding the application team
- B. Objective comments regarding the application work
- C. The inspector's personal opinions of the application team
- D. No comments regarding the application team
正解：D
質問 # 27
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- B. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- C. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
- D. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
正解：C
質問 # 28
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Dragging a gauge through wet coating
- B. Using a damaged gauge
- C. Placing the gauge along the longitudinal axis
正解：A、B
質問 # 29
The initial steel condition is important to the NACE Inspector because:
- A. If the steel is pitted more coating will be required
- B. It affects the final appearance after blasting
- C. The Inspector may have to reject the Steel
- D. Less abrasive is need if the mill Scale s gone
正解：C
質問 # 30
Solvents are added to coating formulations to
- A. dissolve binders and form liquid coatings.
- B. decrease film permeability.
- C. increase film permeability.
- D. provide color.
正解：A
質問 # 31
Check abrasive blast pressure with a
- A. surface comparator
- B. replica tape
- C. nozzle aperature gauge
- D. needle pressure gauge
正解：D
質問 # 32
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
正解：A
質問 # 33
ISO SA 2 is defined as:
- A. Light Blast Cleaning
- B. Near White Metal Blasting
- C. Thorough Blast Cleaning
- D. Very Thorough Blast Cleaning
正解：C
質問 # 34
......
NACE-CIP1-001コーティング検査官レベル1試験は、認定されたコーティング検査官になるために必要なトレーニングと知識を個人に提供する認定プログラムです。この認定は世界的に認められており、コーティング検査産業で雇用を求める個人に最適です。認定プログラムは、表面処理、コーティングアプリケーション、検査技術を含む幅広いトピックをカバーしています。
NACE-CIP1-001問題集には100%厳密検証された問題と解答で合格保証もしくは全額返金：https://www.goshiken.com/NACE/NACE-CIP1-001-mondaishu.html
合格させるNACE NACE-CIP1-001試験には練習テスト問題集豪華お試しセット：https://drive.google.com/open?id=151TFBxjVKiaMF-ofv3ktnYMxArFffxud